All Installation Instructions for General Electric Microwave JVM3670BF09

Customer:: charlie from spring, TX
Parts Used:: WB24X830, WB24X829
Difficulty Level:: Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

no hot

every thing is working, but no hot

Was this instruction helpful to you?

Customer:: James from Fall Branch, TN
Parts Used:: WB27X10928
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

microwave just stopped working

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

Was this instruction helpful to you?

Customer:: Henry from Cedarburg, WI
Parts Used:: WB27X10810
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Completely dead, no display

Uninstalled microwave from above range, removed cover then vent assembly (slide slightly to the left to free it). Opened the control panel (slide up then tilt forward) to access the troubleshooting/repair/test sheet. Followed the diagnostic flowchart and determined the TCO above the cooking cavity had failed. No other faults found. Ordered part Sat. afternoon and rcvd it Monday. Part is held in place with spring clips and quick connect terminals so installation was easy. Microwave was back in operation in no time.

Was this instruction helpful to you?

Customer:: Emanuel from Woodstock, VA
Parts Used:: WB06X10436
Difficulty Level:: A Bit Difficult
Total Repair Time:: More than 2 hours
Tools:: Screw drivers

Converted an over the range microwave from non vented ductless to outside vent.

Installation of the damper was effortless but removing the microwave, cutting holes vertically through an overhead cabinet then installing ducting with a ninety degree bend, through another cabinet, and then through outside wall consumed most of the time and effort.Your service, packaging, and timely (next day!) were extremely helpful.

Was this instruction helpful to you?

Customer:: Prashant from Dardenne Prairie, MO
Parts Used:: WB24X829
Difficulty Level:: Really Easy
Total Repair Time:: 1- 2 hours
Tools:: Pliers, Screw drivers, Socket set

Microwave would not turn on

Microwave would not turn on. Lights and fan worked fine. Before the microwave stopped completely, it would turn the microware fan on even when door was open. I read the reviews and they were exactly the same issue that others were facing. Once I opened the front panel and got to the switches it was easy to figure out which switch was bad as it was the one that was soft (When clicking it). It was hard to take it out though (it seemed stuck). So, I used a plier to yank it out. I put in the new switch and everything worked just great! I would like to thank other comments that were left on the site to make my task much easier. Thank you (to the commenters on PartsSelect), you not only saved me money, but also ensured that I learn about the microwave more and give me the confidence that I could fix it.

Was this instruction helpful to you?

Customer:: Timothy from Middletown, NJ
Parts Used:: WB24X829
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers, Wrench set

Light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up

It was a snap using the instructions given. The key is getting into the unit. I did have to use a multimeter to find the failed switch since there are two of that type.

Was this instruction helpful to you?

Customer:: Cathy from San Diego, CA
Parts Used:: WB02X10753
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Metal flap would not close.

My son fixed it in less than five minutes! easy!

Was this instruction helpful to you?

Customer:: Charles from Chester, VA
Parts Used:: WB27X10810
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

No Power to Microwave

Microwave would not turn on--No lights--Nothing worked 1. Removed screws from back and side and pull off microwave cover. Be careful! There HIGH voltage back there due to a large capacitor that stores power. This capacitor is charged up even with Microwave unplugged. I checked the fuse located on top back part of Microwave. A lot of the time this is the problem but this time the fuse was good. I used an Ohm meter to check to see if there was an open circuit in one of the Thermostats. There are two of them in the Microwave. The Thermostats are about the size of a dime. One is located on the top right side and the other is on the top left side. One of them was bad. I ordered a new Thermostat. It arrived in just 2 days. I installed it and the Microwave was repaired and working great.

Was this instruction helpful to you?

Customer:: Helen from Reno, NV
Parts Used:: WB05X10007
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

latch on door broke

replacement door recommended $308.00 ! said no parts available ! I looked online and found one for $ 35.00 ! then i found your site and bought it for $3.00 !!! It came very fast. We looked up schematics on your site and looked on u tube for video of how to repair it. and my sons put it together in 15 minutes thank you!!!!!

Was this instruction helpful to you?

Customer:: ronnie from terlingua, TX
Parts Used:: WB06X10144
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

couper on turntable had broken into.

took part of put new part on.30sec to do.

Was this instruction helpful to you?

Customer:: Stephanie from Kernersville, NC
Parts Used:: WB27X10928
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

microwave won't heat

bought a fuse but that didn't solve the problem. Guess I need a new microwave

Was this instruction helpful to you?

Customer:: Albert from Smithfield, RI
Parts Used:: WB06X10144
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

broken coupler

simply remove broken coupler and install new coupler. no tools required.

Was this instruction helpful to you?

Customer:: James from Newbern, NC
Parts Used:: WB06X10436
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

change microwave fan discharge from front to top

damper plate was a snap-in part. rotated fan discharge to top of microwave. installed ducting to discharge food odors outside.

Was this instruction helpful to you?

Customer:: Jesus from Casa Grande, AZ
Parts Used:: WB07X10881
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Had an F3 message error...Beep...Beep. Really annoying it can happen when the kids or anyone cook someting without turning on fan and flame is higher than pan size, which cause the control panel to get extremely hot and causes a short

The exact part I needed was only 80 bucks or so, but I went ahead and got the whole assembly for 130 so I would not have to wait an extra 2 wks and risk having to stick it on the other assembly. I received the part fast, cuz it was in stock, just connected the smart board to it and attached the every connection. I screwed it back in place and put all the screws back in and bam!!!!. Just like new, no more beeping and everything is great. I did run a cooking 101 with everyone here to make sure they always turn on fan and make sure flame is under the pan size.

Was this instruction helpful to you?

Customer:: Donald from Otsego, MN
Parts Used:: WB06X10144
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

coupler broke

removed the bottom of the microwave and removed the motor and replaced the coupler and reassembled. Easy repair.

Was this instruction helpful to you?

JVM3670BF09 General Electric Microwave - Instructions