JVM3670WF10 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Timothy from Middletown, NJ
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up
It was a snap using the instructions given. The key is getting into the unit. I did have to use a multimeter to find the failed switch since there are two of that type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from Piscataway, NJ
- Parts Used:
- WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Powered Off completely
After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Easton, PA
- Parts Used:
- WB06X10288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace bottom grease filters
Just pull down on "O" ring tab and filter will release. Install new filter in same position. you may have to pull on "O" ring to complete fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from East China Township, MI
- Parts Used:
- WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All power to the microwave went out.
PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from New Boston, OH
- Parts Used:
- WB27X11068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
smoked high voltage transformer,main board, and magnetron
replaced board and transformer with new parts, replaced magnetron with used
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juli from San Diego, CA
- Parts Used:
- WB27X10810
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to the microwave
Trouble shot first by removing the digital read out face plate panel, lifting it up and out. Found the thermostat housed on the bottom section (found a picture of what I was looking for). It had two connectors. Removed the connectors and noticed that the one looked burnt/melted that was on the thermostat. Took paper clip, connected it with the wires to bypass the thermostat. Plugged in the microwave and power returned. Yes! Ordered thermostat part and changed it out. The new part didn't have a piece that fit exactly into the floor of the microwave so I just made sure it was secure to the bottom. It is only attached by 1 small screw. Fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Iraj from Houston, TX
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass turntable coupler
Very simple it took me less than 5 minutes to fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Socorro, NM
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Quit working
Just like the directions said. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- irving from DELRAY BEACH, FL
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turn coupler broke
lowered bottom plate of microwave then unscrewed little motor. put the new coupler in the hole from inside of microwave, then pressed the motor shaft on to the coupler .then just screwed it all together again.simple and no straining
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from ScotttsDale, AZ
- Parts Used:
- WB49X10063
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken platter in micro wave
Very easy ordered on line placed it in microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from San Jose, CA
- Parts Used:
- WB06X10288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace grease filter
slipped them into place by hand
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Cedarburg, WI
- Parts Used:
- WB27X10810
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Completely dead, no display
Uninstalled microwave from above range, removed cover then vent assembly (slide slightly to the left to free it). Opened the control panel (slide up then tilt forward) to access the troubleshooting/repair/test sheet. Followed the diagnostic flowchart and determined the TCO above the cooking cavity had failed. No other faults found. Ordered part Sat. afternoon and rcvd it Monday. Part is held in place with spring clips and quick connect terminals so installation was easy. Microwave was back in operation in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kernersville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Williamstown, NJ
- Parts Used:
- WB27X10880, WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Not heat ! ,bad magnetron
Pull cover off , located the bad magnetron . Then replaced it with the new one. About 15 min. Of work.
Was this instruction helpful to you?
Thank you for voting!