JVM3670WF10 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from East China Township, MI
- Parts Used:
- WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All power to the microwave went out.
PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Mt. Vernon, IN
- Parts Used:
- WB06X10144
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The turntable coupler broke off the shaft
Once we noticed the turntable not working I removed the piece and noticed it was broken at the base of the coupler, took a vacuum and removed the broken piece and installed the new part. Thanks for the help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Spring, TX
- Parts Used:
- WB06X10144
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic turntable coupler broke
1. Unplug the microwave or switch off the breaker to the microwave. 2. Unscrew 5 screws on the bottom plate of the microwave. The plate swings down by the hinges on the back. 3. Unplug the wires leading to the turntable motor and make note of which color wire goes on which side of the motor plug. 4. The initial instructions said unscrew the screw holding the motor but my model has two screws. Remove the screws and lower the motor. 5. Insert the plastic coupler from inside the microwave through the hole in the center of the base. The coupler has a half moon shaped female shaft that connects to the male shaft that extends up from the motor. Slide the motor shaft into the plastic coupler. 6. Replace the screws that hold the motor onto the base of the microwave. 7. Plug the power wires back into the motor with the wires in the correct position as noted above. 8. Plug in the microwave and turn it on to check if the turntable now turns. Mine did not at first so I unplugged the microwave and the motor wires. It turns out you can plug the motor wires in and they don't connect correctly. I reconnected the motor plug and plugged the microwave back in and turned it on. This time the turntable was working. 8. Replace the five screws on the bottom plate of the microwave. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Concord, CA
- Parts Used:
- WB27X10597
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Not heating
Removed the above stove microhood. Removed the side panels & the top panel. Diode located on right hand side of microwave. Removed with screwdriver & replaced new diode. It's best to get the microwave schematic online to pinpoint location of the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from San Jose, CA
- Parts Used:
- WB06X10288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace grease filter
slipped them into place by hand
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Yuma, AZ
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The turntable wouldn't turn.JVM1730Dm1cc
I followed the online instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Socorro, NM
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Quit working
Just like the directions said. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from Oceanside, CA
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Coupler was broken and wouldn't turn the glass turntable
Just replaced the old and broken one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter e from far hills, NJ
- Parts Used:
- WB06X10288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Air/Grease Filters Were Worn Out
Rec'd the parts within a day or two after ordering and simply placed them where the old ones were removed and wala my stove is back filtering. Only problem, the oven won't ignite while the broiler and stove top burners are fine. Go figure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juli from San Diego, CA
- Parts Used:
- WB27X10810
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to the microwave
Trouble shot first by removing the digital read out face plate panel, lifting it up and out. Found the thermostat housed on the bottom section (found a picture of what I was looking for). It had two connectors. Removed the connectors and noticed that the one looked burnt/melted that was on the thermostat. Took paper clip, connected it with the wires to bypass the thermostat. Plugged in the microwave and power returned. Yes! Ordered thermostat part and changed it out. The new part didn't have a piece that fit exactly into the floor of the microwave so I just made sure it was secure to the bottom. It is only attached by 1 small screw. Fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEOFFREY from PLANTATION, FL
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass Turntable Coupler Broke Into 2 Pieces
Simple, simply lifted the old piece out of position and dropped the new piece in. A small part of the broken old piece must have fallen away and is still in the unit, but it has not gotten in the way of the new piece doing its purpose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Dublin, OH
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass cooking tray broke
I laid the new tray in the microwave. There was nothing to really install....but, the woman I spoke to in order to order the tray was terrific and I had the part in two days!! I would recommend this company every time!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Nashville, NC
- Parts Used:
- WB27X10810
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
miccrowave would not run.
removed housing. saw t-stat was burnt. replaced t-stat by removing mounting screw and installing new t-stat. reinstalled mounting screw. reinstalled oven housing. 15 minute job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Effingham, IL
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The glass turn table coupler (drive) broke - no table turning.
Lifted off the glass turn table and just pushed the new plastic couple onto the drive post. The plastic coupler is splined, so just sit it onto the drive post and lightly turn it until it starts to drop and give a little downward push. That's it - about 30 seconds and the table is turning again.
Was this instruction helpful to you?
Thank you for voting!