JVM1490BH02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pearlie from Beulaville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Timer, light and control pad worked. Turn table and heat did not work. Oven would not start up.
I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followed them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from LA VERNE, CA
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Unit would not heat
Used a Motor cycle Jack to remove both unites combined. Removed side panels exposing internal working parts. Removed nonworking Magnetron and replaced it with new Magnetron. The process was completed in about 1 hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from HILTON HEAD, SC
- Parts Used:
- WB10X10021
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door latch assembly
Read other folks on your site on how they did it and I followed their directions. About 30 minutes and it was done. Figured I saved lots of money. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from CHARLOTTESVLE, VA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light Bulb appeared to be burned out
The Halogen Light Bulbs for lighting the area below the microwave seemed to be burned out. I order new bulbs but by the time they arrived the old bulbs appeared to be working again. Not sure why this happened but I have new bulbs if they become burned out for good at some point.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Spartanburg, SC
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass turntable broke when being washed.
Ordered the part on Monday, it was delivered on Wednesday, only paid for standard shipping. All I had to do was put it in, right part, back to new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andrew from HOMOSASSA, FL
- Parts Used:
- WB56X35363
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
installed new kitchen cabinets
the problem was the mounting bracket that was installed when the house was built ,was not the bracket that came with the microwave. It was used to step the microwave out 3" in front of the other cabinets for the style that they were using then. so when I was installing the new cabinets I didn't want that style, so I ordered the original mounting bracket. It was a perfect fit and the install went great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from ITHACA, MI
- Parts Used:
- WB20X10048
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Thermostat quit.
Checked all sensors with a multi-meter, found the thermostat to be the problem, no continuity.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Bedford, NH
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulbs burnt out and needed to be changed
Ridiculously easy, unscrew, and change bulbs. Having the correct bulbs made all the difference, I did not have to waste time looking for the correct one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Ashland, VT
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bulbs for sueface light burned out
Removed screw holding faceplate that covered bulbs. Next inserted new bulbs into sockets.
Turned on surface light to insure they worked - they did. Re-attached faceplate.
Turned on surface light to insure they worked - they did. Re-attached faceplate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Esther from Brooklyn, NY
- Parts Used:
- WB06X10311
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
cover fell apart
removed screw from inside wall. removed leftover board & replaced with new board & screw. good as new!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mack from Jacksonville, FL
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
No heat.
Replaced the fuse. Result; did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma from De Moines, IA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The halogen bulb had blown
It was just a matter of removing the old bulb and easily putting the new one in place. Very simple repair and the bulb was received amazingly fast. Was no doubt the best service I have received and I appreciate the quick response.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DOMINICK from VENICE, FL
- Parts Used:
- WB25X10019
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bulbs Burnt Out
Removed old bulbs replaced with new. Bulb fit perfect thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilbert from Stephens City, VA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Bulbs Failed
Used a phillips screwdriver to remove the screw holding the light cover in place. Removed the two bulbs and replaced them. Closed the cover and tightened the screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Swampscott, MA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
microwave lamp was burned out
took glass cover off being an electrician and saw lamp or bulb was burned out. googled your site and with model number.went on partselect found lamp,orderd it.2 days later lamp arived installed lamp. So easy no running around or making several calls
Was this instruction helpful to you?
Thank you for voting!