JVM1630CD004 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cody from Omaha, NE
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn table stoped functioning
Troubleshooting process:
Using a screw driver I opened the bottom of the unit using a Philips screwdriver and unhooked the drive motor electrical connector. Using a multimeter I checked to ensure power to the motor. This confirmed that the motor is bad and must be replaced.
Repair process:
After receiving new motor I removed the old motor and installed the new one using a Philips screwdriver and closed up the bottom cover.
It functioned good as new. Relatively cheap and very easy fix.
Using a screw driver I opened the bottom of the unit using a Philips screwdriver and unhooked the drive motor electrical connector. Using a multimeter I checked to ensure power to the motor. This confirmed that the motor is bad and must be replaced.
Repair process:
After receiving new motor I removed the old motor and installed the new one using a Philips screwdriver and closed up the bottom cover.
It functioned good as new. Relatively cheap and very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from huntersville, NC
- Parts Used:
- WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bulb was stuck in the lamp
First I removed the screws that were underneath the microwave. Once I did that I disconnected the wires to the bulbs and removed the screws that were attached to the holder lamp. replaced the parts and reversed the process. It went really smooth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Muskego, WI
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cooking tray drive motor did not work.
Unpugged microwave. Removed the screws on the bottom cover of the micorwave. Unpugged drive motor and removed two screws from drive motor. Installed new motor and replaced the bottom cover, plugged in microwave . . . presto!
Installation was just as easy as numerous other customers indicated. Also, your service was as great as many other customers indicted . . . part was recieved in 2 business days. Thank you for great service and website.
Installation was just as easy as numerous other customers indicated. Also, your service was as great as many other customers indicted . . . part was recieved in 2 business days. Thank you for great service and website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Fort Smith, AR
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb burned ot
Un screwed the cover but when i tried to remove the bulb it was broken at the base. I disconnected the power and used neddle nosed pliers to remove the base
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teddy from CLERMONT, FL
- Parts Used:
- WB24X830
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fan was running when I opened the door.
I replaced the switch at the bottom per instruction. I had both switches. I think it was the monitor door switch.It works fine now. Thank you Part Select .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Fountain Hills, AZ
- Parts Used:
- WB24X829
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Micrwave won't run - turntable turns backwards when door opened...
Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Albuquerque, NM
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Power worked but would not cook
Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Austin, TX
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inside Bulb went out.
Remove top air grate via 2-screws. Remove metal top panel behind grate that's above bulb via 1-screw. Bulb is exposed and can be un-screwed. DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Hanover Park, IL
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave appeared to work. Fan worked, timer worked plate rotated. It just didn't heat the food!
I purchased the fuse and 3 door switches from PartSelect. Replaced the fuse first but that did not solve the problem. Then I replaced the 3 door switches and problem solved!! So fuse only cost $5.00 so glad I have a new fuse in there as well. To see how to replace door switches see videos on utube!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- selwyn from inglewood, CA
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass Carousel Cooking Tray Broke
I replaced old tray with new. Received replacement part in two days. I was surprised at the quick response time. The part ordered was right the first time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Streamwood, IL
- Parts Used:
- WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Left light socket was damaged beyond repair
Handed the part to my son. He unscrewed 5 screws in the base of the microwave, it dropped down. The light mechanism was clearly in view. With the exception of some corrosion on the old piece, it was simple to remove and replace, put back together, screw back up and all worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from CICERO, IL
- Parts Used:
- WB08X10016
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bulb broke in socket, socket had deteriorated beyond repair.
Phillips screws on bottom panel allowed me to install new socket and put electric connection back. Secured bottom panel and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Marco Island, FL
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass carousel cooking tray shattered
It took less then 10 minutes to order. Received new part with 3 days
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Lakeland, FL
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dropped and broke glass carousel tray
Put it in place. Ordered replacement over internet on Wednesday and part arrived Friday. Very fast service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACK from ETOWAH, NC
- Parts Used:
- WB06X10144
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable quit turning.
Disconnected power cord from receptacle. Removed 5 screws in bottom panel and allowed it to swing downward on rear hinged edge. Disconnnected power wires to motor. Removed screw to detach motor. Inserted coupler through hole beneath center of turntable. Inserted motor shaft into coupler and re-attached motor. Connected power wires to motor and then closed the bottom panel and re-inserted the 5 screws.
Was this instruction helpful to you?
Thank you for voting!