JVM1861WD002 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- BRUCE from MONROE TWP, NJ
- Parts Used:
- WB06X10144
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
part was cracked
removed old part and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Tucson, AZ
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass cooking tray stopped rotating
I removed the microwave oven from the wall by unscrewing a trim plate or frame that surrounds the face of the oven. Pulled the oven out of the cabinet. Removed the glass cooking tray and rollers from the oven interior. Turned the oven on its side to expose the bottom. I unscrewed the small cover plate in the middle of the bottom which exposed the turn table motor. The motor was attached by two screws and a connector plug. In a couple minutes I removed the motor and replaced it with the new one and reassembled the oven. I put it back in the cabinet and it works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Highlands Ranch, CO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable quit working
Took the bottom of microwave off unplugged motor replaced it with new one (two screws) plugged it in replaced bottom and ther you go saved $240.00 over the local appliance repair company. Thanks Mike,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith A from LAKEWOOD, CO
- Parts Used:
- WB36X10163
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb went out
Opened the light cover. Removed the old light bulb using a light tug on the old bulb, lined up the new bulb and pushed gently into the socket.
Turned the power back on and the microwave is good to go.
Turned the power back on and the microwave is good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janice from GOLD RIVER, CA
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I thought I had pushed the timer button for 20 minutes duration period,
however, I had hit the cook button and the microwave did not have an item to cook inside. Resulted in shattering the glass tray and meting the plastic lid sitting inside which was fused to the cooking tray. Carefully wrapped up the shattered tray and melted lid in heavy paper, deposited it into the garbage, then happily placed my new E.O.M. glass cooking tray into my G.E. Profile microwave. Thank you .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Cincinnati, OH
- Parts Used:
- WB02X10733
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water dipenser valve leaking.
Replaced the filter cartridge.Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from LEWISTON, MI
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The center of turn table broke. A small plastic part that goes under the glass in center.
We took out the broken part, it came right out,and put new part .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrence from Milton, FL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Excessive noise while driving the glass tray.
Straight forward repair. The item came quickly, and since I had taken the other motor out previously to test it, the instalation was a breeze. There are a total of 7 external screws for the cover and two internal that hold the motor in place. One screw driver is all you need and access to the bottom of the microwave (I was fortunate that mine was an above the range model so accessing the bottom was easy). Anyone with a little manual dexterity can handle this repair now problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from oak lawn, IL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
G.E. microwave turn table was loud and not working
I took it apart and found a small electric motor was not working . I couldn't find it locally so I ordered it from partselect and it was here in just a few days.the repair was easy only a few screws and plug it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Vista, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drive tray table failed to turn
unplugged the appliance, removed the glass tray from inside, turned the microwave on its side and removed the 3x3 panel, removed the drive motor by taking out two screws and disconnecting the two electrical wires, compared the new item with the old one, placed new in olds position and screwed in place. replaced the 3x3 cover, turned microwave upright, plugged in the power cord, placed a cup of water on the tray, turned the microwave on for 30 sec. and watched the table turn. Very simple and convenient application.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Fort Stewart, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave noisey
Removed 5 screws to allow lower pan to hang down. Unplug motor, remove 2 more screws that hold motor in and pull it out. and reverse process for reinstallation of new motor. Took all of 4 minutes allowing time to drink a beer while taking the new motor out of the box
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from Colorado Springs, CO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass cooking tray not turning
First I removed the 6 screws that hold the bottom panel in place. I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and then connected the two wires to the new element. Secured the element in place and replaced bottom panel.
Real simple process!
Thanks!
Real simple process!
Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from MANDEVILLE, LA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
it broke after 3 days and i was denied a new part or refund
it was easy . i unsrewed 2 srews and it went right in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from Sparta, AL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the glass cooking tray would no longer move.
We removed the vents from under the bottom and then the 4 screws and pulled the motor out. It was a no brainer to fix and the part came in alot faster than expected.
Thank You
Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Cleburne, TX
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave was making a koud grinding sound
First I unplugged the microwave from the wall receptacle. Next I removed eight screws that let the bottom plate of the microwave hood pivot down with its hinges. Next I removed two screws holding the turn motor in place. I then unplugged the motor and replaced it with the new motor and reversed the above procedures until everything was back in place. I then turned the microwave on and was thrilled to find it working properly again.
Was this instruction helpful to you?
Thank you for voting!