JVM1442AA01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marvin from Bradenton, FL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable motor burned out
Told by appliance repair service that parts were very expensive and service call started at $80 minimum. Finding replacement motor on your site was very easy. Instructions on repair were very complete and included pictures of the motor itself which had same capacity as replacement motor. Before ordering part from PartSelect I followed the online instruction for repair/replacement of the Microwave table motor and it was exactly as described. Removed filters and 10 screws with a single Phillips head screw driver. Motor looked the same as picture and ordered it. Part arrived in 24 hours and it took 4 minutes to replace the motor from start to finish. Total costs including shipping was approx 40 dollars. Great service and great site. This is my second repair using PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Manassas, VA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Grinding noise, tray didn't always turn.
Repair was simple. Remove screws on bottom panel of microwave, let cover hang on hinges. Remove two screws from drive motor, remove old motor, insert new motor, replace two screws, then reattach bottom panel. Done!
Quiet has returned to my microwave:-)
I also discovered that the (night light) bulbs are much easier to replace when the bottom panel is lowered.
Quiet has returned to my microwave:-)
I also discovered that the (night light) bulbs are much easier to replace when the bottom panel is lowered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Cary, IL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
motor that rotates glass cooking tray was not working
Disconnect the power cord. Removed the screws locate under the spacesaver microwave. The bottom will swing down and hang off the hooks on the back edge. Disconnect the wires plugged into the broken motor. Remove the two screws that hold the broken motor in place. Replace with new motor and re-insert screws and motor wires. Reassemble bottom panel and plug power cord back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Canal Winchester, OH
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Micro Glass Tra Y Quit Rotating.
Took out the screw holding the old motor, unpluged it and reversed the procedure to install new part. My wife is now very happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from Summerdalr, AL
- Parts Used:
- WB26X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Water had got on motor thru air vent, shorted out
Replace ventilator motor. No problem when you have correct part.
Thanks for the fast service.
Thanks for the fast service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Raleigh, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave Food Turntable Not Working
Reviewed the current postings surrounding the problem i was experiencing on your website. Located the 5 phillips head screws on the bottom panel. Removed them letting panel hinge down, removed the motor connector and checked for 21V AC with Volt Meter confirming the motor was not operable. Ordered replacement motor which arrived 3 days later during the holidays. Repeated the panel removal then removed the moter retaining screw and replaced with the received part a perfect matching. All in both panel removals for diagnostics and replacement of the motor took about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon F. from Brookline, MA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right hand surface lamp burned out. It apparently fald up and broke the glass cover. I wne on line when I found out the only local deaaler was some miles away and more expensive.
Simple. The parts came instantly. The glass was too big so I had it cut to size. I unscrewed the fixture with a screw driver replaced the bulb and slipped the glass cover into the frame and screwed the whole assembly in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lake Sherwood, MO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The turntable began operating intermittently and making noise
The repair was extremely easy. Remove seven screws in the bottom trim, slip the electrical connector off and remove the two screws holding the motor. Slide the new motor into position, replace the connector and screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Colorado Springs, CO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable motor quit working
As others have desribed - remove 5 screws from the bottom cover. Lower cover and replace turntable motor with 2 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Troy from Zieglerville, PA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced drive motor on GE Spacemaker microwave
I thought this would be a major project but tured out to be very simple - 7 screws, 10 minutes and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from Silver Spring, MD
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
glass cooking tray not rotating
Removed screws from bottom of microwave. Had to invite my neighbor over to remove one of the screws... he used his impact drill.
Found out that the motor was working fine. It was the brown piece that the glass cooking tray sits on that was broken.
I had removed the glass tray and tried to pull out the brown piece...but, it wouldn't come out and so I assumed that it was intact and thought that the motor wasn't working.
It's great that it's so easy to return parts to PartSelect.
Found out that the motor was working fine. It was the brown piece that the glass cooking tray sits on that was broken.
I had removed the glass tray and tried to pull out the brown piece...but, it wouldn't come out and so I assumed that it was intact and thought that the motor wasn't working.
It's great that it's so easy to return parts to PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from New York, NY
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The turnatable stopped rotating; GE said to buy a new micowave, that it would cost just as much to fix.
The delivery was lightening fast...which I didn't expect. Great service.
First I shut the circuit breaker off for the microwave.
I then removed the six screws on the full undermount. The motor was visible; it was simple to unscrew the 2 screws on the motor; pulled it away from the wire/plug and disconnected it.
It was just as simple to plug the new motor in, then screw the unit it place with the 2 screws.
That was it...just replaced the undermount and turned the cicuit breaker back on.
And to think GE said to buy a new one!
First I shut the circuit breaker off for the microwave.
I then removed the six screws on the full undermount. The motor was visible; it was simple to unscrew the 2 screws on the motor; pulled it away from the wire/plug and disconnected it.
It was just as simple to plug the new motor in, then screw the unit it place with the 2 screws.
That was it...just replaced the undermount and turned the cicuit breaker back on.
And to think GE said to buy a new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from Palm Harbor, FL
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass cooking tray broken
First and foremost the service was superb. Ordered on a Monday and had it on Wednesday - WOW. I opened the package and put it in the microwave.
I thank you very much for your fast, efficient and professional service.
C. Brown
I thank you very much for your fast, efficient and professional service.
C. Brown
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from Mount Pleasant, SC
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced Glass Tray
Just put the new tray in and it fit perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Waldorf, MD
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Interior Light Out
Removed Cover Plate,
Removed back cover
Bulb disintegrated removed base with pliers
Screwed in new lamp
Replaced cover
Done
Removed back cover
Bulb disintegrated removed base with pliers
Screwed in new lamp
Replaced cover
Done
Was this instruction helpful to you?
Thank you for voting!