JVM1442AA01 General Electric Microwave - Instructions

Removed six screws that allowed the "bottom" to swing down; then removed the two screws holding the motor - disconnected the two wires. Installed the motor and reversed this procedure to finish the project.

Let me keep this short and simple.

Disconnect the power to the microwave
Remove the (7) screws from the bottom panel
Disconnect the wires from the old Drive Motor
Remove the retaining screws of the drive motor
Then install the new drive motor in the reverse order

Removed the 5 screws that held the housing so it dropped down. removed the 2 screws to the motor. Disconnedted the plug. reinstalled the new motor. connected the plug and raised the housing and replaced the 5 screws. Took less than 10 minutes start to finish. Piece-of-cake.

removed the srews under the unit unplugged the rotor motor and unscrewed 2 screws holding in the motor. When new motor arrived I plugged it up and put it on with the 2 screws and then put the bottom filter screen piece back on with the 6 little screws. REal, real easy.

easy repair. removed seven screws on the underside of the microwave and lowered the bottom cover. removed two screws from the old motor, unpluged the wires. reversed this sequence to install. took less than 5 minutes.
I had previously read these steps others had posted on partselect so the job was a breeze!

took screws out of bottom of microwave.dropped down bottom cover to get at drive motor I took out one screw droped down cooking tray motor disconnnected 2 wires reconnected put back up and put 1 screw in ,fastened bottom and was fixed very easy ,and parts select is the best place to find what you are looking for if I ever need parts this is where I will order from service is great and only took about 2 days to receive my part .I went to store where I bought my microwave and they wanted to sell me a new one.saved over $200

Unplugged microwave from the wall. Removed the screws on the bottom of the oven. Detached the light, removed the bottom panel. Unscrewed one more screw on the turn table motor and twisted to remove. Plugged in the new one and reattached the Electrical wires and bottom panel. Piece of cake. Just don't forget to reconnect the lights!

ha to remove the bottom ,to get at the internal screws that held the drive motor. after disconnecting the power to the moter, i removed the two screws that held it in place. i installed thre new motor , reconnected the wire plug to motor . replaced the outer screws, and the project was done.

ordered part from partselect received in about 3-4 days removed 6 ea screws from lower panel , removed 1 ea screw holding motor in place, pulled wire receptacle loose from motor, threw old motor in trash, put new motor up into plastic tray rotating device turned motor to secure on one side and installed screw to hold motor reinstalled wire plug and panel ops ckd good about 15 minutes to do could have done it quicker but my eyes ain't what they use to be Very easy fix when you get the right part and I got it on the first order with partselect ......Thank You Very Much

I removed the screws (7) around perimeter of bottom. Don't remove the middle screw as it holds some gizmo in place. Dropped down hinged bottom. Removed motor (2 screws and a plug) matched to picture on website and ordered.

2 days later, part arrived, installed, good to go.

Bill, Kentucky

The Glass cooking tray was very noisy. This was verified by turning off the tray rotation.

1. Removed the two metal filters.
2. Removed the screws holding the bottom cover of the microwave. 6 or 7 I believe.
3. Removed the two screws holding the drive motor in place.
4. Started the microwave with the motor hanging down to to verify it was defective. I could hear the motor rotating and making noise.
5. Replaced the motor, bottom cover, & filters in reverse order.
6. Tested, Works fine!

Remove the 8 screws in the bottom pan covering the bottom, unpluged the lights and motor plug-ins, slid or pulled the pan forward or to me and removed pan. prized the triange piece which fit into the glass tray to turn it to remove it. removed the two screws which held the motor in place. presto, got the model # off the inside panel and ordered the part on the compiiter, \. arrived in 5 days.
P.S. cleaned everything while I had it apart, toke longer than chancing the part.

Dropped the bottom of the microwave,removed the two screws holding the motor in, disconnected the electric wires, reversed the procedure and it worked like new!

-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order

I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followed them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.