EMO3000HSS03 General Electric Microwave - Instructions

I just simply took out the two screws that were holding the grille in place and placed the new grille the tightened up the screws.

I tried to install the new part several times, but it didn't work. So I used a pencil to move things around down the shaft. After that the new part went in and now my microwave is doing what I need it to do.

Took out the door to be able to replace the door latch. After removing the plastic cover it was challenging to remove the broken latch (unlike other models this has two separate latches individually controlled by spring. The pin holding the latch was impossible to take out and I figured I need to take out inner layer of the door frame (metal part) to remove it. But the frame was stuck and did not come out. I found no reference how to do it on internet and then with another pair of hand pulled outwards while simultaneously pulling upward. Was finally about to pull just enough and replace the latch and push the metal frame to fit back.

ordered 2 new sockets and bulbs easy replacement great service from this site

Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.

Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.

Just removed the screws from botton of unit, unplugged and removed the burned up motor, reveresed the process to install new motor. Less than 10 minute job.

bought a replacement for it

Removed 5 philip head screws from under panel. Under panel droped down exposing drive motor. Removed one drive motor screw, replaced with new motor at the same time lining up new coupler. Pressed together, reinstalled motor srew, attached wire coupling and tested. Worked fine. Reinstalled lower panel screws (5)and unit was ready to go. I ordered two of each units because I believe this to be weak link in the unit. It was only 2 years old, used little as I have another home. I recently installed a like unit (Hanging) and it was a breez. 4 srews properly placed, electrical cord hole properly drilled & ready to go in 45 minutes.

Changed the bulbs and it still wouldn't work. Checked voltage coming from board to the lights and did not have 110 volts. Several relays on board that operate the fan and various other components and all those were working properly. Checked voltage leaving board and did not have any voltage. Thought it may be the board. After replacing the board noticed a burn mark on back of board under the relays.

Checked pricing from GE, Sears and Parts Select. Parts select was a lot cheaper price and exact replacement part. Shipping cost was reasonable and quick.

I diagnosed the problem myself. I googled GE parts and was refered to you guys. I ordered the part and it took less than a 5 days to arrive. I used a phillips scewdrive to remove the cover of my microwave and removed the turning glass motor. This took less that 30min and cost less that $50.00. I figured that it would have cost me approx $125.00 to get a tech person to my home for this repair.

Thanks a lot!

Bernard

Unscrewed 2 retaining screws from old grille and discarded old grille. Moved new grille into place and aligned screw holes and secured screws into place.

removed the bottom plate from microwave and replaced parts

I took the glass table up and underneath was the turntable coupler. I reached in with my hands and gently pulled the old coupler out. Once out I lined up the new one and gently pushed it in the hole until it locked into place. The process took about 5 minutes to complete. Very easy to install.

I removed the screws that held the bottom in and then dropped it down to access the motor. I removed the 2 screws that held the motor in and unplugged it. I then plugged the new one in and reattached it with the 2 screws and put the bottom back on. It took me about 5 minutes to fix it for only $40.00.