JVM3670CF08 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Socorro, NM
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Quit working
Just like the directions said. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- irving from DELRAY BEACH, FL
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turn coupler broke
lowered bottom plate of microwave then unscrewed little motor. put the new coupler in the hole from inside of microwave, then pressed the motor shaft on to the coupler .then just screwed it all together again.simple and no straining
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from ScotttsDale, AZ
- Parts Used:
- WB49X10063
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken platter in micro wave
Very easy ordered on line placed it in microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Chester, VA
- Parts Used:
- WB27X10810
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Power to Microwave
Microwave would not turn on--No lights--Nothing worked 1. Removed screws from back and side and pull off microwave cover. Be careful! There HIGH voltage back there due to a large capacitor that stores power. This capacitor is charged up even with Microwave unplugged. I checked the fuse located on top back part of Microwave. A lot of the time this is the problem but this time the fuse was good. I used an Ohm meter to check to see if there was an open circuit in one of the Thermostats. There are two of them in the Microwave. The Thermostats are about the size of a dime. One is located on the top right side and the other is on the top left side. One of them was bad. I ordered a new Thermostat. It arrived in just 2 days. I installed it and the Microwave was repaired and working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronnie from terlingua, TX
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
couper on turntable had broken into.
took part of put new part on.30sec to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Middletown, NJ
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up
It was a snap using the instructions given. The key is getting into the unit. I did have to use a multimeter to find the failed switch since there are two of that type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from Piscataway, NJ
- Parts Used:
- WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Powered Off completely
After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Easton, PA
- Parts Used:
- WB06X10288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace bottom grease filters
Just pull down on "O" ring tab and filter will release. Install new filter in same position. you may have to pull on "O" ring to complete fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from East China Township, MI
- Parts Used:
- WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All power to the microwave went out.
PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Otsego, MN
- Parts Used:
- WB06X10144
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
coupler broke
removed the bottom of the microwave and removed the motor and replaced the coupler and reassembled. Easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from San Diego, CA
- Parts Used:
- WB02X10753
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Metal flap would not close.
My son fixed it in less than five minutes! easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter e from far hills, NJ
- Parts Used:
- WB06X10288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Air/Grease Filters Were Worn Out
Rec'd the parts within a day or two after ordering and simply placed them where the old ones were removed and wala my stove is back filtering. Only problem, the oven won't ignite while the broiler and stove top burners are fine. Go figure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Yuma, AZ
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The turntable wouldn't turn.JVM1730Dm1cc
I followed the online instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Spring, TX
- Parts Used:
- WB06X10144
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic turntable coupler broke
1. Unplug the microwave or switch off the breaker to the microwave. 2. Unscrew 5 screws on the bottom plate of the microwave. The plate swings down by the hinges on the back. 3. Unplug the wires leading to the turntable motor and make note of which color wire goes on which side of the motor plug. 4. The initial instructions said unscrew the screw holding the motor but my model has two screws. Remove the screws and lower the motor. 5. Insert the plastic coupler from inside the microwave through the hole in the center of the base. The coupler has a half moon shaped female shaft that connects to the male shaft that extends up from the motor. Slide the motor shaft into the plastic coupler. 6. Replace the screws that hold the motor onto the base of the microwave. 7. Plug the power wires back into the motor with the wires in the correct position as noted above. 8. Plug in the microwave and turn it on to check if the turntable now turns. Mine did not at first so I unplugged the microwave and the motor wires. It turns out you can plug the motor wires in and they don't connect correctly. I reconnected the motor plug and plugged the microwave back in and turned it on. This time the turntable was working. 8. Replace the five screws on the bottom plate of the microwave. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Nashville, NC
- Parts Used:
- WB27X10810
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
miccrowave would not run.
removed housing. saw t-stat was burnt. replaced t-stat by removing mounting screw and installing new t-stat. reinstalled mounting screw. reinstalled oven housing. 15 minute job.
Was this instruction helpful to you?
Thank you for voting!