JE1860W General Electric Microwave - Instructions

It was so easy to order a new glass plate ! Love this web site,

It took quite a bit longer to decide which one of the roller guides in the selection was the right one, than to install the new one. Got it right though, works great

Replace the fuses

Replaced the fuse. Result; did not fix the problem.

I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

Our GE Profile Advantium 120 Series Over-the-Range Microwave stopped working. We called GE Service. The first available appointment was two weeks after our call. The technician charged $99, gave us a form stating that the Magnetron and Diode Cable as defective and quoting an additional price of $362 to furnish and install these parts. He said that it would be another two weeks before he could do the work. Instead I ordered the parts from you and had them within two days. The parts you furnished were identical to the original parts in our unit. They arrived within two days. I installed the parts without removing the microwave from the wall. The most difficult part was inserting the magnetron mounting screws into openings in the rather tight space available. I was able to do this by using plastic pacaging tape to hold the screws onto the end of a short Phillip screw, Prior to iserting each screw I pushed it through the sticky side of a piece of packaging tape. I then folded the sticky surface over the shank of the screw. Once a screw was seated, but before it was fully tightened, I used needle nose pliers to pull off the tape. The unit now functions perfectly.

Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.

I ordered a new one by calling the 800 number, gave them my model number and ordered a new one on the phone and paid with my credit card. It was shipped the same day and I received it on the second day by Fed-X.

I removed the new tray from the box and slid it into the microwave. That's it.

PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.

Very easy you just have to make sure that the tray is in the groves for the wheels :)This is the best place to shop as I have used them on all kinds of appliances and they have never let me down when it comes to price and delivery time!

After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.

bought a fuse but that didn't solve the problem. Guess I need a new microwave