RM955PXPW0 Whirlpool Microwave Oven Combo - Instructions

Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!

Removed old element, replaced new element. Unfortunately, this didn't fix the problem. It was the temperature sensor. But now I have a new bake element, though!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

The removal of the old burner and installation of the new burners was easy. Just lift the opposite side that rests on the rim and pull burner out. New burner then gets inserted and the opposite side goes right into rim. It took all of 30 seconds to replace both burners. I wish I had replaced these when they first started to go!!

Problem I had was finding the right ones to fit the stove top. Burner pans that tell you will fit most stoves, do not. After I had paid over $20.00 for some that did not fit, I got on the internet, found you, ordered the replacement parts and had them within a few days. Put them in and there you go. A perfectly happy me and a nice looking stove again.

As soon the Bake Element has arive, I install it no more than 5 min... All I nedd was a Screw driver. It was so easy, Thank You PartSelet!

was very easy to install I only needed a phillips screwdriver to remove old part and install new one.

Removed block (1 screw) Cut 2 connecting wires. Strip insulation. Attach new block with wire nut(per enclosed instructions) Heat shrink wrap with Lighter. attach block. 10 minutes: problem solved

I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:

Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.

removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair

It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him

Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.

Removed all surface burners from range, removed range top screws, and suspended range top. Removed plug-in block mounting screw. Cut wires for plug-in block close to original wire-nut junction. Inserted contacts & wires from kit into plug-in block. Slid a provided shrink sleeve onto each wire. Stripped wires on range wires and then connected them to the plug-in block wires with the provided high-heat wire nuts. Selected one of the two provided plug-in block brackets that matched the original bracket on the range. Used a butane lighter to shrink the shrink sleeves over the wire nut connections. Snapped the appropriate bracket onto the plug-in block. Reassembled everything in reverse order and plugged in new element. Note: my only two issues are that the two high-heat wire nuts provided in the kit were a bit too small for the wire gauge in my Whirlpool range. It took some fiddling on my part by carefully re-stripping the range wires to get the wire nuts twisted on securely. Two more wire nuts of the next size up would have been appreciated. Also, I found that the provided plug-in block mounting screw did not find fit my range. No problem; I simply re-used the original screw. All in all, an easy repair and the element works perfectly.

I followed the instructions provided.

The new handle, braces and screws arrived as quoted. My son-in-law installed the new one without much trouble. The handle is black and matches the black front of my stove. The older handle was sort of a wood-brown. Thus I like the new one better. Thank you for good service and prompt attention to the problem.
Linda Archibald
Hanson, MA