RM955PXPW0 Whirlpool Microwave Oven Combo - Instructions

took out the old heating elments and cleaned the bottom & top of oven with out the elments in, which made it alot easier then put new ones in. They were very easy to do, just make sure you watch how you took old ones out and don't loose the screws cause you use them to put new ones in.

Open oven door. Still power to the wall, but all Knobs in "OFF" position. two phillips screws, pull old element back, and disconnect both leads. Put the leads on the new element and reinsert with two mounting screws. Simple.

Replaced with the new burner works like new. Thanks a bunch!

The broiler unit had disintegrated at both connections. I removed the two screws in the top of the oven holder the unit, pulled out the unit, measured and ordered a replacement.

To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).

Unplugged old burner elements. Popped in new burners. Turned on the burners to test.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Not only it was easy to install but to find them was even quicker, thanks to Part Select.com. After searching for quite some time I found the site and my problem was solved. Item was received in a timely manner and replacing was very quick.
Thank you.

1. Turn off oven.
2. Switch off circuit braker to oven.
3. Remove two screws holding element.
4. Pull element out to expose connectors.
5. Disconnect connectors and remove element.
6. Reverse procedure for installation.

I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked. Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.

Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!

pulled out the old burner, plugged in the new burner. Turned on the power and it heated up very quickly.

Before ordering any parts I remembered seeing a fan above the nylon roof of the microwave. I had seen a belt that drove it on a prior repair 3 years ago.

I then removed 1 screw holding the electrical panel so I could tilt it open. Since power was still plugged in I didn't put my hand in. I used a flashlight and the broken belt.

I could also see the moter that turned the belt and tested it by starting and stopping the microwave and could see the motor pulley spin when it slowed to a stop. I then closed the control panel and screwed it in place.

That confirmed I proceded to go to the internet with the model # for the rane/microwave and looked for parts.

I had an easy job looking the part and saw that the fan as I had called it was named Stirrer because it kept stirring the microwaves over the food.

Overall I looked at 2 venders and chose Part Select because they showed the same catalog page and part numbers, and they had a better price.

I had my part/ belt in 4 working days and installed the new belt in about 15 minutes. This time unplugging the range so there was no power to be concerned with. It was a matter of picking out the old belt and putting the new belt on the motor then walking the belt over the large pulley at the Stirrer since the belt will stretch a bit.

Buttoned it up and later tested with popcorn and it left only a small amount of old maids.

Thanks, Walt

Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.

Problem I had was finding the right ones to fit the stove top. Burner pans that tell you will fit most stoves, do not. After I had paid over $20.00 for some that did not fit, I got on the internet, found you, ordered the replacement parts and had them within a few days. Put them in and there you go. A perfectly happy me and a nice looking stove again.

It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him