RM235PXL0 Whirlpool Microwave Oven Combo - Instructions

I just removed two screws and disconnected the push on clips I then cleaned the botton of the oven and replaced the element. And it works just like new.

removed racks and door (could have left door on but made it easier to reach screws) removed 2 screws from old element unplugged the 2 wires and reversed process for new element.

I unscrewed the two screws holding the element in place and disconnected the two wires. Removed the element from the oven and replaced with the new one. Plugged in the two wires and replaced the two screws that secures the element to the back of the oven. Turned on the oven to test and turned back off when satisfied everything was O.K. Easy job.

Removed 2 screws on heating element mount plate. Pulled out heating element 3 inches and used needle nose pliers to remove the 2 connector clips. Reconnected connector clips by hand to new heating element. Put heating plate back into original position and reinstalled 2 mount screws.

Funny, I suppose. We decided to buy a new stove given the old age of the old one. Problem is, on delivery day it wasn't delivered and we discovered that there wasn't even one in the warehouse. At that point we got ticked and decided to look into the problem. The website led us right to the problem. We ordered, the part arrived the next day and the replacement was simple. Just unscrew the holder inside the over, unplug the old element and plug in the new. I needed needle nose pliers because one of the wires slipped behind the insulation. We also bought a thermometer and found that the calabration was right on the money. Happy campers... we saved $400.

Found breaker box and shut off power to stove, Check to make sure you turned the right breaker off before you attempt to put you hands in it, also make sure all the switches on the stove are in the off position . Open Oven Door, I used a Phillip screw driver to remove the two screws holding the Bake element in place . pull out to reach wire connections and gently pull connectors from element. Remove the old Bake element and Install the New one,by reversing process in removing the old one. after you have it back in place turn breaker back on at breaker box turn oven control to Bake setting, turn Oven Temperature control to around 200 degrees and Element should began to glow bright orange, job complete, it's that easy!~

Turned off electric to oven by shutting circuit breaker.Opened oven door, took out baking racks,loosened bolts from rear of oven holding element and plate . Disengaged element with plate from wires at rear of oven. Attached new element to clips on wires, rescrewed element plate back to rear wall. replaced racks and turned on circuit breaker. DONE!
Thanks for the quick service ordered one day, next day delivery, never missed a meal or dessert.

un plugged oven from wall Unscrewed 2 screws pulled out old heating element and plugged in new heating element then plugged stove back in

1) Turn off the power at the circuit panel!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!

It was so easy. I removed the baking racks. Then I unscrewed two Philips head screws that held the rack in place. Then I pulled the two connections apart from the wiring. Plugged the new element into the wiring. It was as simple as sliding it in and out, replaced the screws, and within minutes I was back to baking again.

This repair couldn't be easier. I turned off power to the range, removed the oven racks, unscrewed the two screws holding the element, carefully slid the connectors off of the terminals, reconnected them to the new baking element, put the screws back in. Entire repair took less than 10 min. Not much harder than changing a light bulb. Works like a brand new oven.

I took out 2 screws and installed new element! It took 5 mins.

removed old bake element (remove two screws, disconnect two wires. install new element connect wires, replace screws to hold in place. turn on oven to be sure it works.

Removed the two sheet metal screws holding the element, Unplugged the contacts and plugged and fastened the new element.

Made sure that "Breaker" for oven is in the off positon.

Opened oven door to the first "stay open" position...lifted door straight up...and off of the hinges....which removes the door....and allows easier access to oven.

Removed oven racks

Removed two philips head

Pulled burned out element toward the front of the oven.....exposing the two connector wires.

Used pliers to pull wire connectors from burner element connectors.

Reversed the order of this process....to install new element.