CCE701 Maytag Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linda from BURSON, CA
- Parts Used:
- WPA3167501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Light bulb went out in mictowave
Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Gastonia, NC
- Parts Used:
- 866294
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Range oven door switch need replaced
I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top; and close lid. Part #866294
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mr. Mike F from SAN ANTONIO, TX
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door hinge
My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from IDAHO FALLS, ID
- Parts Used:
- WP5700M600-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Door Glass Broken inside
Removed the door removed 2 inner panels Installed and reassembled A Cake Walk NOTE be careful not to strip threads
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from DIAMOND BAR, CA
- Parts Used:
- WP74003387, 866294
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Oven switch not working
Had to remove the glass top and the control panel and the panel bracket then use angled needle nosed pliers to compress the retainers then pull the switch from the inside of the oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edie from SANTA FE, NM
- Parts Used:
- WP701650
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Replacement of old oven door seal
Removed door (that was the most difficult part)
Took out lots of screws to disassemble
Cleaned all the components that were now exposed
Put new seal in place
Put parts back together with screws
Put oven door back
Excellent!!
Took out lots of screws to disassemble
Cleaned all the components that were now exposed
Put new seal in place
Put parts back together with screws
Put oven door back
Excellent!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Rocklin, CA
- Parts Used:
- Y701721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the fan started making noises like it was shaking
I pulled off the facia from the microwave/oven. Unscrewed the plate holding the microwave and slid out the microwave. The microwave and oven are a unit. I unscrewed the oven from the hole it sits in and slid out the oven and set it on a sturdy chair. Then I unscrewed (6 screws) the bracket that holds the microwave to the oven. After that I unscrewed (14 screws) the top sheetmetal plate on the oven and slid that around behind the oven. Then I unscrewed the grounding strap inside. Did the 2 screws on each side of the oven holding the fan unit and slid that out. Undid the 2 wires plugged into the motor and the 2 screws holding the fan motor. Then I slid off the fan from the old motor and slid it onto the new motor and reversed the whole process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from GAINESVILLE, FL
- Parts Used:
- WPY04100020
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned out/arced
Removed old element, 2 screws, cleaned oven , 60 minutes, replaced with new element, working like new, wife thoroughly impressed...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Cameron, OK
- Parts Used:
- WPY04100020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element quit working
Removed the original element with a screwdriver and disconnected the 2 wires, it took about 2 minutes. Got online with PartSelect and easily matched a replacement part. Ordered the part and received it within a couple of days. Very impressed with the ease and quickness of the order processing and shipping. Took the new element and connected the wires, screwed the 2 screws back in, it took about 2 minutes. Turned on the oven to check and everything worked perfectly. Very happy with the overall experience with PartSelect. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from California, MO
- Parts Used:
- WPY04100020
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner out
repair was simple two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dane from Evansville, WI
- Parts Used:
- WPY04100020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not heat
Checked the element to see if it was open or no
resistance, it was open
e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
resistance, it was open
e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deidre from Brownsville, TX
- Parts Used:
- WPA3167501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave oven bulb had burned out
My Dearest One removed the screws that held the part that covers the bulb; removed the old bulb, put in the new bulb and replaced the cover.
The whole operation took less than 5 mins.
Thank you.
The whole operation took less than 5 mins.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Newark, DE
- Parts Used:
- WPY04100020
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Replaced the heating element
It would have been a very easy job if the one wire had not fallen inot the back. I could not reach it and fried to figure out how to get in the back to no avail. Finally I took a piece of wire coat hangerm and bent it and then fished it out. The packing around the hole compressed while I was trying to get the wire and I thought I wpuld have to replace it, but overnight it resumed its original size. It should have probably taken less than thirty minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Huntington Beach, CA
- Parts Used:
- WPY04100020
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven failed to heat
First, I tripped the oven circuit breaker. Then I removed the two screws that hold the element in place. Then I pulled the element out about 5 inches and disconnected the two wires. At first, I had to figure out how the wires would disconnect. Once I removed the heating element, I reversed the procedure, tightened the screws, reset the circuit breaker, and set the oven to bake. The element began to function, and I knew Imy efforts were successful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!