LRM1250B (CB1ELGA) LG Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Virgil from Bowling Green, MO
- Parts Used:
- 6549W1S011B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Turntable not turning.
Take off cover then the bottom. Transformer is on the bottom plate and wires won't let it come all the way off, too many wires to pull off so will have to position the bottom plate so you can get to the motor. Remove 1 screw on motor and remove motor. Install new motor connect wires replace bottom plate, replace cover. All done (hope & pray it works ok) mine worked perfect. Hope this helps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelia from Streamwood, IL
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
no heat
unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Oak Ridge, TN
- Parts Used:
- 3B74133Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Microwave operated but did not heat
Initial failure of over range microwave Aug 3rd. Control Panel worked but no heat. Took to local LG authoriaed local repair place. They fixed it quickly and we re-installed it. Worked fine for 2 months then had similar failure again. Agaim took to same authorized repairer. They kept unit for 3 months but finally concluded theu could not fix it and suggested we contact LG for a partial refund. When they tested the unit during re-assembly in my presence, there was a blue flash and the fuse blew. Since we had built a custom tile mural back splash around this unit, I brought it home, ordered a number of time delay fuses new capacitor and two new high voltage diodes. However, using my Fluke DMM, I checked the existing capacitor and high voltage diode and they checked OK so I just replaced the time delay fuse. The high voltage transformer leads had 2 possible ways to connect to capacitor and diode. Tried one way, plugged unit in and turned it on, and immediatly blew the fuse. Replaced the fuse and reversed the high voltage transformer connections,amd turned unit pn, and it worked perfectly. Since we had experienced several power failures during the time of the original failure, the repairer concluded that power spikes might be at fault, so I also purchased a TrippLite ISOBAR4ULTRA 3300 Joule surge protector between wall outlet and microwave, and re-installed over range. It has worked perfectly since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Houston, TX
- Parts Used:
- 6549W1S011B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Replace turntable motor
Unplug.Take off the external cowling from the back of the unit by removing the torx security screws. Tip: instead use a thin screwdriver blade to unscrew the torx screws, or knock out the center pins of these screws. Remove the bottom panel. The replacement motor is attached with one phillips screw, re-attach wires to motor - polarity doesn't matter. Re-assemble and you're finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from NORTH BEACH, MD
- Parts Used:
- 6930W1A003X
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Thermostat needed to be replaced
We had made this determination with the help of a repairman on the phone. I ordered the part and waited for it. It was stuck in West Virginia. After several days after it was expected a repairman fixed my range to the tune of $168. It should have cost $30 (the cost of the part and shipping).
Unfortunately I probably won't order from PartSelect again.
Unfortunately I probably won't order from PartSelect again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Hampton, VA
- Parts Used:
- 5020W0A001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door button - the one you push to unlatch and therefore open the door, was broken.
The old button fell out because the "tabs" on the end of the posts that come out from the button had broken off. These "Tabs/posts" hold it in place - you'll see how when you look at it. All that was necessary was to put the springs from the old one onto the new one. Make sure to put the thing in right-side up; there are two "tabs/posts" on the top side, and one on the bottom. Gently slide it into position as nearly straight as you can, squeezing the "posts" until they clear the front of the opening. Continue to slide in EVENLY until you feel the part "click" into place. That's it! I recommend cleaning out the area fully before installation, with a a god household cleaner, and also putting a thin coat of some sort of lubricant on the part before you put it in. (You won't be able to do that after it's installed.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yolanda from Birmingham, AL
- Parts Used:
- 5889W1A003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
didn't have it at time of pruchase
brought new one and the help with the sites pictures to describe what I need was extremely helpful. The prompt delivery was great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONAND from OVERLAND PARK, KS
- Parts Used:
- 5020W0A001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Microwave Button had broken plastic hooks causing it to pop out.
Replaced Microwave Button with new button and hooks. Repaire took one min. by just pushing the new button on the Microwave and it hooked on and did not pop out. Good for another 4 years maybe!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kiah from CARPINTERIA, CA
- Parts Used:
- 5889W1A003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic base that rotates under the glass plate broke.
Lifted up the glass plate, lifted out the plastic base that rotates and placed the new one inside. The piece that connects is shaped like a semi-circle, so I rotated it until is dropped into place. Then I put back the glass plate and it was finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Pickens, SC
- Parts Used:
- 3390W1A012G
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
turntable inop due to broken glass tray.
Put on safety glasses AND leather work gloves. Grab pliers. FIRMLY grasp the110 A/C power cord with jaws of pliers, squeeze and pull plug from 3prong power socket. Carefully press black bar on front panel to open oven door. Stand back so door doesn't strike your face . Lift out damaged glass tray with BOTH gloved hands..place in re-cycle bin. Open parts package carefully and install the NEW glass tray. Plug 3prong plug BACK into 110v outlet and press start button........Stand back! View the new glass tray turning in a circular fashion through the heat/radiation proof front door. Job well done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from northfield, VT
- Parts Used:
- 6549W1S011B, 5889W1A003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
AC Syncro motor went in microwave
I tested the motor with an OHM meter, saw it was shot. Broke the turntable off when I tried to take it out from inside where it's attatched to the drive motor.( The plastic was like glued or welded onto the shaft of the original motor ) Had to open up the removable trap door on the bottom to pull the one screw that holds the motor in. Swapped it out, pushed the new turntable back in, and turned it on. Works like new! great parts, fast shipping, great deal !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henriette from Davis, CA
- Parts Used:
- 5889W1A003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
super easy
saved me having to buy a new microwave. It was super fast delivery, had the part the next day! Amazing service and great customer support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Minneapolis, MN
- Parts Used:
- 5020W0A001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The button that opened the door had plastic hooks break off.
I looked up the part number, with shipping it came to $16, and in one minute of installation time, I just gently pushed the button into the front using the original springs that pushed the button back out, and it just clicked into place, the microwave back in action.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from minneapolis, MN
- Parts Used:
- 5020W0A001B, 4B72023B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door button retaining clips broke off. button would fall out of place
Inserted spring on middle post on button back side. Pushed button/spring into hole on front of microwave until clips engaged and snaped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Monticello, IL
- Parts Used:
- 6549W1S011B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Turntable quit turning
Overall repair quite simple. Removed screws from the sides and rear of the microwave, then removed cover. Next, removed only the screws to separate the bottom cover. Removed the one screw in the AC Synchronous motor to remove the motor (had to use small screwdriver through a vent slot in the bottom to remove the screw). Unplugged and removed motor. Installation is the reverse of removal. Note: on the back of my appliance were 4 torx screws with a tamperproof pin in the center. I used the rotary tool to grind out the pins so I could use a regular torx bit instead of ordering specialty bits.
Was this instruction helpful to you?
Thank you for voting!