LMV2015SW (00) LG Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Susan from HENDERSON, NV
- Parts Used:
- 6549W1S013H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave dish would not move back and forth
unscrewed the bottom of the microwave and unplugged old part then took the screw out and put new one in. Super easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vic from Allen, TX
- Parts Used:
- 6600W1K001D, 6600W1K001C
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When the MW door was opened a fan would start running. Close the door the fan would go off.
Removed the MW from the wall. Took the top screws off the air vent. Then removed the two screws holding on the display. I then moved the display to its side and it revealed the micro switches. I removed the plug in leads from the micro switch one at a time. I did this with all three micro switches only one at a time. I reinstalled everything and plugged it in. No more fans starting when the door is opened.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SEVERN, MD
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
food does not get hot, carousel did not turn, all other indicators worked
Read the troubleshooting section on this site. Figured it was an interlock problem because the food was not getting hot (magentron not turning on) and the carousel was not turning. Did not think both the carousel motor and magnetron failed at same time, thus indicated an interlock problem. The interlock switches are actuated by the door latch. Replaced the assembly locker piece with all three switches (only a $20 dollar part) and microwave was fully operational again. Wife and kids think I am a hero.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from ORCHARD PARK, NY
- Parts Used:
- 6600W1K001D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Door switch was burnt out
Removed outer cover
removed lower door switch
installed new switch
Wa La!
removed lower door switch
installed new switch
Wa La!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from NEWARK, DE
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would not heat and made a buzzing or popping sound
Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from SANBORN, NY
- Parts Used:
- 6324W1A001L, 6600W1K001D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the turn table no turn and no heat the food. but the bottom oven worked
well I unplugged the microwave one day prior to working on it. shock precaution smart way to do this job. very easy pullout the screws behind the unit pull off the outer casing. minor screws inside the unit you have to remove a couple things out of the way. unplug the magnetron and remove first gives you more room to work on the side panel to replace the micro switches. I only replaced one the bottom micro switch. only one bad, but since I was in there I clean the bulb and changed the magnetron any ways. I read other reviews and made my choice to do so. it works perfectly now. Thanks PartSelect for having parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from DEPEW, NY
- Parts Used:
- 6600W1K001D
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not start when closing door.
Removed some cosmetic panels. Removed the assembly with micro switches. Examined the faulty switch by checking the clicking action of switch. Two others were ok by this method. Replaced the switch with new one. Works fine so far. Thanks to web site and YouTube videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from CRYSTAL LAKE, IL
- Parts Used:
- 6600W1K001D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Items were not getting heated up in the microwave,
I went to LG website enter model number and was given a list of parts that need to be replaced with a percentage of which part fails the most. I order micro switch PS3522738 which arrived and PS3529293 was backordered. I installed the one that arrived. The microwave worked briefly. I reordered and waited for both switches to arrive and installed both. The microwave still doesn't work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from PINELAND, SC
- Parts Used:
- 6600W1K001D
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door switch malfunction
Take cover off microwave. Check door switches to determine which one was faulty.Remove and replace faulty switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from KENT, WA
- Parts Used:
- MEB41908101
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
AFTER 3 WEEKS I'M STILL WAITING FOR THE REPLACEMENT HANDLE
WHEN ARE YOU FINALLY GOING TO GET AROUND TO SENDING MY PART? HOW CAN I REPAIR THE MICROWAVE WITHOUT THE $35 PART I PURCHASED FROM YOU? PLEASE SEND MY PART IMMEDIATELY BEFORE I PHONE BBB AND JD POWERS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from LA VERNE, CA
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Unit would not heat
Used a Motor cycle Jack to remove both unites combined. Removed side panels exposing internal working parts. Removed nonworking Magnetron and replaced it with new Magnetron. The process was completed in about 1 hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter J Baxter from Billings, MT
- Parts Used:
- MEB41908101
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
First problem was removing the vent cover. There were four screws that were not obvious that held the cover on. Reinstalling the cover also proved to be difficult due to alignment problems. Once that was done, the second problem was removing the door. There is a small, almost invisible, latch that h
At home on the kitchen counter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from OLD TOWN, FL
- Parts Used:
- 3861W2A006A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
quit working
the repair kit was useless the toggles were to big to go through the top the threads on the bolts interrupted the toggle i had to drill the holes thole to except the toggles I got bolts at the hardware store what a mess
Bob
Bob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Colonia, NJ
- Parts Used:
- 6600W1K001D
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
suddenly stopped working while in use
i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in and it worked.i then installed the new switch and closed up the outer shell
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irving from BEDFORD, NH
- Parts Used:
- MJS47373302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken glass
Just replaced the inner turn table glass tray
Was this instruction helpful to you?
Thank you for voting!