LMH2016SW ((00)) LG Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kevin from Colonia, NJ
- Parts Used:
- 3B73362F
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
suddenly stopped working while in use
i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in and it worked.i then installed the new switch and closed up the outer shell
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from CRYSTAL LAKE, IL
- Parts Used:
- 6600W1K001C, 3B73362F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Items were not getting heated up in the microwave,
Easy, and the microwave still doesn't work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Anchorage, AK
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replacement of Magnetron
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marianne from CHURCH HILL, MD
- Parts Used:
- 6912W1Z004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
light bulb replacement
very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from NORTH BEACH, MD
- Parts Used:
- 6930W1A003X
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Thermostat needed to be replaced
We had made this determination with the help of a repairman on the phone. I ordered the part and waited for it. It was stuck in West Virginia. After several days after it was expected a repairman fixed my range to the tune of $168. It should have cost $30 (the cost of the part and shipping).
Unfortunately I probably won't order from PartSelect again.
Unfortunately I probably won't order from PartSelect again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Windham, NH
- Parts Used:
- 3B73362F, 6600W1K001C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Had to lift on the door for the microwave to run, suspected the door switches.
Ordered the switches from Partselect, arrive in two days. Had trouble removing the plastic connectors from the old switch terminals, one of the plastic protectors broke, but was able to reuse it. It took a little figuring out how to remove the existing switches. Must push in a tab and rotate the switch on a little pin, then remove. Must be careful not to break the plastic tabs holding the switches in place. Replaced all (3) switches at the same time. All in all it was pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glynda from Walsenburg, CO
- Parts Used:
- MEB41908101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle broke off microwave door.
Removed one panel and screws from broken door. Attached new handle and replaced panel by snapping in place...Very easy to instll..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Cedar Park, TX
- Parts Used:
- 3B73362F
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Microwave failed to head and light, fan, and turntable failed to come on.
Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Jacksonville, FL
- Parts Used:
- MJS47373304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass tray broken
really easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Burke, VA
- Parts Used:
- 6912W1Z004B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb burned out
I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelia from Streamwood, IL
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
no heat
unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from Daleville, VA
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave would not heat food, but everything else worked.
Problem was a faulty door latch switch. I easily accessed the switch by removing the control panel, total of 4 screws. After that, just disconnected the three switch door latch assembly and connected the new one. Took about half an hour and was very easy. Unit works perfectly now.
Was this instruction helpful to you?
Thank you for voting!