KEMC378KWH02 KitchenAid Microwave Oven Combo - Instructions

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.

Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on

My oven (late 90's/early 2000's model) didn't have the flip-down hinge locks shown in the video. It seems Whirlpool/Kitchenaid changed the hinges even though they didn't change the model number of the oven. With my style hinges, you have to put Allen wrenches or bent nails in the holes just behind the hinge pins. Then close the door almost all the way and lift it out to separate the hinges. Spring force holds the nails in tightly until you replace the door. This video was very helpful:
https://www.youtube.com/watch?v=p7oRZdIN6m0

Also, my door had 3 different kinds of sheet metal screws. Two of them have similar heads but different threads. Keep track of which is which for when you put everything back together.

I followed the instructions per a YouTube video. My older model was slightly different in parts used in the video, but the general idea was the same. Very happy with current repair / parts. The door now opens smooth as glass, and I even got a chance to clean some internal parts inside the door.

https://youtu.be/tAypQqC5cxo?si=YoDaVMHtalPP3mhO

Watched the repair video and started the project. Ran into a problem when trying to remove the interior panel off the door to reach the broken interior glass. On this model Kitchen Aid there is another section that is screwed in holding the exterior glass pieces in place. It prevents the interior panel from coming off the front of the oven door. So we had to flip over the door and unscrew the glass retaining bars to get the interior panel off and reach the glass. This allows the entire door to come apart in pieces so you have to carefully line up everything to re-assemble the door. Part of the issue with this is some of the retaining screws are not very long so you have to press the pieces back together to make sure the screw will catch in the original hole. We had to do this twice to ensure the interior door glass was laying flush on its mounts. A bit fiddly for sure, and if I was working alone it may not have been successful. But at least we know how the door is put together!

I follow the directions on the Maytag site. It is a very simple job. I appreciate the Information I got from Becky when ordering the hinges.

This is a microwave/ Oven slide in unit. You DO NOT need to slide out the unit, the repair can be done from inside the oven. Just be careful on pulling the wires from the unit so they do not break. I used shrink wrap over the joints but you can use tape as long as it can take the temperatures

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

took the plate out of the shipping box, inserted it in the microwave

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

We had to remove screws from the vent covers above and below the microwave, then there were 2 screws (one on each side) that attached the microwave to the oven. Once all of the screws were removed we had to pull the microwave out. Then we pulled the light cord out, removed the burnt out light and installed the new one. Then reversed the steps.

Taking off the glass lense for the light bulb was harder than I thought. It unscrews counterclockwise, but it was very hard to get off. It would not turn. I ended up using connector pliers I use for work, that has rubber jaws. The lense unscrewed very easy with it. Light also unscrews out. PartSelect.com is the only way to go to buy parts for appliances. It is simple, even has the illustrated parts catalog. And it saves a lot of time and gas, driving around looking for the part!!. PartSelect came through again.

We followed the instructions given by Parts Service. The only problem we had (Whirlpool left two screws out of spacer bracket and it fell out requiring further removable of inner glass to replace spacer. Process took about twenty minutes.

no repair needed - ordered part, came within 3 days - very satisfied

Easily replaced after received the product from Part Select. Very satisfied.