W221-C Jenn-Air Microwave Oven Combo - Instructions

Al lI had to do remove the oh swith & attach th e new on & push in place
It took about 5 min. to turn off the electric & to turn it back on.
Glen V

I read the online instructions sent in by previous diy'ers. the repairs, esp. the heating element replacement went just as described and went really well. I have used the oven and it works beautifully. Total cost of parts was a little over $60.00. Piece of cake!

We took the door off, you have to be careful of the hinges popping back. We put small screwdrivers on each side and held the hinges out, this made the door easy to just stand up and slide back on the hinges. The glass replacement was simple just a few screws. We spent $127.00 on the part and shipping and a new wall oven would have cost us $1500.00. Thanks for making this part available.

My husband removed the old element and replaced it with the new one. I think he used a screw driver to remove and replace. The part shipped and arrive in 5 days. Quick and easy!

The most difficult part of the repair was removing the two Phillips screws that attached the element to the back wall of the oven. With some WD40, and a hammer to tap on the screws through the screw driver (and several hours) the screws finally came loose. Once the screws were out it was a matter of removing the two wires connected to the element and reconnecting the wires to the new element. After removing the screws this job took less than 5 minutes.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

We removed the 2 screws at back of oven that hold element on, which took some doing as they were very rusted. We then pulled old element out; this proved a bit difficult because the ends of the old element were stuck in the insulation behind. We had to wiggle the old element back and forth a bit to get it loose from the insulation. Other than that, it was easy.

I had repair men replace the door hinges 2times and decided the 3rd time to do it myself and save some $. ordering was a chinch, received the parts in 2 days and followed instructions posted on this site. They were excellent. Just a few things I would stress: Lift UP the door to remove, not open the door fully and pull out and also make sure to take the small pins out of the new hinges before closing. They are so small you could over look them. The person who put detailed instructions on this site is to be commended for clarity and detail on "How To" I really appreciated it.

Remove screws, remove old coil, place new coil, screw back in. The hardest part of this task is removing the existing screws which are most likely partially corroded and hard to move.

The heating element in our old old oven broke in half. Luckily we were able to find a replacement part (which we didn't think we would that's how old the oven is)! The part arrived within a couple of days, my husband removed the old element (toughest part was getting the two old screws unscrewed) plugged in the new one and he was done. Took about 5 minutes! I turned on the over to test it was connect properly and it started heating up right away! We are VERY happy !! :o)

Removed racks from oven, unscrewed two screws holding old element in place with philips head screw driver from the back wall of oven. Carefully pulled element from oven to expose connecting wires and then pulled two wires loose from old element. Reconnected wires on new element and carefully reinstalled element to rear of oven interior with two screws removed from original element.

opened the door; put 12 penny nails in each hinge through the holes for it, removed screws above hinges; slid door off; laid it on a towel on the workbench; removed side/top/bottom screws and laid the outer door aside. removed the screws from the inside of the door, laid the inside glass aside, removed the glass assembly (broken), cleaned the loose glass out, laid the new glass assembly in place, replaced the panels and screws and slid the door on the hinges, removed the nails and closed the door. 35 minutes. Never did it before4. Part fit great! Thanks to partselect for having the discontinued part!

The repair was straight forward. Remove about a million screws and several layers. The only challenge was loosening some baked on screws in the innermost layer. Repair would have been less than an hour if not for those screws. Key advice is to pay attention to the order that each layer went back on. My oven/stove is about 25 years old, but works great. The part was backordered at a local appliance part store from May to ???. I ordered it at PartSelect and it was also backordered for a couple of months. I got it delivered to my home from PartSelect before it ever came in from the local store.

Opened oven door. Inserted a small bent nail into the small holes on the hinge. This locks the hinge from closing all the way. Removed the chrome hinge retaining plates. One at each hinge. Lifted the door off the oven. Laid door on towel. Removed 3 screws from the top of door, three screws from the bottom of door. This allows you to separate the two pieces of the door. Clean all glass surfaces, including the ones under the middle glass panel. Removed 1 screw from each hinge at bottom of door. Pull hinge from bottom of door after removing screws. Insert new spring at top of door first, replace retaining screw. Realign the two door parts and replace all screws. Set door back on hinge pocket. Be careful to insure that the hinge seats into the pocket. Open door just enough to replace retaining plates. Process was easy, but it did not fix the problem completely. Bought heavy magnets from hardware store and installed them inside the door. This with the new hinge fixed the problem.

Loosen two screws to remove door. Removed outside trim and other outside screws hold center panel in place. Removed one screw holding hinge in place. Screwed new hinge in place. Re-attached center panel to outside trim and hung door. Easy enough.