21336 Jenn-Air Microwave Oven Combo - Instructions

The most difficult part of the repair was removing the two Phillips screws that attached the element to the back wall of the oven. With some WD40, and a hammer to tap on the screws through the screw driver (and several hours) the screws finally came loose. Once the screws were out it was a matter of removing the two wires connected to the element and reconnecting the wires to the new element. After removing the screws this job took less than 5 minutes.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

We removed the 2 screws at back of oven that hold element on, which took some doing as they were very rusted. We then pulled old element out; this proved a bit difficult because the ends of the old element were stuck in the insulation behind. We had to wiggle the old element back and forth a bit to get it loose from the insulation. Other than that, it was easy.

I had repair men replace the door hinges 2times and decided the 3rd time to do it myself and save some $. ordering was a chinch, received the parts in 2 days and followed instructions posted on this site. They were excellent. Just a few things I would stress: Lift UP the door to remove, not open the door fully and pull out and also make sure to take the small pins out of the new hinges before closing. They are so small you could over look them. The person who put detailed instructions on this site is to be commended for clarity and detail on "How To" I really appreciated it.

Remove screws, remove old coil, place new coil, screw back in. The hardest part of this task is removing the existing screws which are most likely partially corroded and hard to move.

The heating element in our old old oven broke in half. Luckily we were able to find a replacement part (which we didn't think we would that's how old the oven is)! The part arrived within a couple of days, my husband removed the old element (toughest part was getting the two old screws unscrewed) plugged in the new one and he was done. Took about 5 minutes! I turned on the over to test it was connect properly and it started heating up right away! We are VERY happy !! :o)

Removed racks from oven, unscrewed two screws holding old element in place with philips head screw driver from the back wall of oven. Carefully pulled element from oven to expose connecting wires and then pulled two wires loose from old element. Reconnected wires on new element and carefully reinstalled element to rear of oven interior with two screws removed from original element.

Removed the screws from the back of the oven to remove the damaged element; removed the electrical connectors and reattached to the new element and screwed it back in

sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks

Replaced oven gasket and both oven hinges. Repairs did not work. Oven door is actually worst. Do not waste your time replacing the oven hinges unless they are actually broken. When to Ace hardware and bought a package of 3 super magnets for about $10. Practice placing the magnets on metal strip on outside of the actual oven vs the oven door. This metal strip is not galvanized for which the oven cleaning latch goes through. Appeared to solve the problem. I then used epoxy glue to insure the super magnets would permanently stay in place. These are dangerous magnets that must be kept away from children and pets. You will spend more time separating these magnets from each other than gluing them in place. This part I will let you figure out but the only way to separate the 3 magnets from each other is the slide them, one at a time, from each other. Now I am awaiting 4 to 6 hours for the epoxy to cure. Best of luck. Jeff

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!

Removed the door by unscrewing two screws holding it to the springs. Then I placed the door face down on a counter top. I removed the screws from each layer of the door and turned each layer over and laid it beside the door. Took care to support glass so it did not fall out and break. When I got to the layer where the seal was, I removed the old seal and replaced it with the new one. Then, I replaced each layer in reverse order. You have to be careful when replacing the layer that goes over the seal that the seal remains in the right place. It has a tendency to slip out of place, so check it before tightening screws. To place the door back on the spring loaded handles, prop the handles open a ways with screw driver handles. This provides a gap so that the door will slip on easily

Placed new knob directly on post. No problem

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.

We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!