EKS396 Caloric Microwave Oven Combo - Instructions

Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.

I replaced the large capacitor (.95 uf). Much of the shell (casing) has to be removed and the capacitor is hard to get to. It is housed in a very inconvenient place. Because of the unfamiliarity of how to access the capacitor it took about an hour to get to it. After receiving the new capacitor it only took about half an hour to install it, re-assemble the microwave, and re-install under the cabinet. Of course a new fuse was required.

Replace the capacitor and the fuse. Then it works again. Part arrived in an open plastic bag with scratch. It looked like a returned part, but it works fine.

My Maytag Microwave UMC5100AD was suddenly broken in 1 second when I heated food last time. Then no clock, etc, seem the fuse broken. to fix it, the most difficult part was how to remove it from the wall trim. Finally got it out. Then went HomeDepot to get the same fuse, replaced and used it, burned again. Then I searched online and ppl said the capacitor might be the one. I took it out and measured it, yeah it indeed was a problem since it's not open. Then I order the capacitor from PartSelect about $32. After 3 days I got it and installed it. Done. Sure need to put the Microwave back to wall trim. That's it. Saved about $500 buck if I buy a new one plus labor to install it. Thanks

I followed the instructions provided.

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!

I took the old wires and plug off and replaced it with the new block it works fine

ordered new broiler pan

Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.

I ordered the part and it was at my door in 2 days. I ordered the part on Wednesday thinking I would install it on the weekend after next. The part showed up on Friday. That was amazing considering I didn't sellect expeidited delivery. I didn't have a manual and have never tried this before so grade my attempt on a curve please. I started by unscrewing the screws closest to the hinge but quickly migrated to the entire face of the range. Pulled the range out and started unscrewing the screws on the side, and then the back. Figuring nothing was coming off and I still couldn't get to the hinge I stopped and regrouped. That's when my wife asked if she could help. I guess I looked distressed. By this time I had removed the drawer and had the range on it's back in the middle of the kitchen with little bowls of screws everywhere. My wife picked up the new hinge and looked it over. Then she started playing with the old hinge which was loose, but I couldn't get it out. She realized that you can remove the old hinge and install the new hinge without taking the whole thing apart. Where was she 30 minutes ago? The hinges came out and the new ones went it in about 10 minutes. It took me another 20 minutes to put back all of the screws I had taken off unnecessarily. Sometimes use your brains instead of a screwdriver. I have the best wife ever!

I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements

I removed the old and repaced with new. I never ordered anything one day and got it the next. I'm impressed

removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.