LT2742A2-96041025200 (2013-08) Jonsered Lawn Tractor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trace from LISLE, IL
- Parts Used:
- 532138971
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Needed to replace the bent blades on my riding mower.
- Made the mower safe to work on the blades (remove spark plug wires, etc.)
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact driver, ..... and you know the rest.
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact driver, ..... and you know the rest.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from EDINBURG, VA
- Parts Used:
- 538691001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Broken weld on right axle
Removed wheel (used strong magnet to catch the keeper)
Removed axle assembly from its mounting tube
(used strong magnet again to prevent keeper lose)
Installed replacement axle (again with the magnet)
Lubricated with 90 SAE
Re-installed the wheel (used magnet again to hold the keeper.
Mowed the lawn.
Removed axle assembly from its mounting tube
(used strong magnet again to prevent keeper lose)
Installed replacement axle (again with the magnet)
Lubricated with 90 SAE
Re-installed the wheel (used magnet again to hold the keeper.
Mowed the lawn.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from ROCKTON, IL
- Parts Used:
- 532140294
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench set
Broken v-belt for drive
I returned the belt because it was the wrong part. Ordered the correct belt from another source. After that the replacement went well and I crossed off Parts Select from my list.
Was this instruction helpful to you?
Thank you for voting!
Dryer runs no heat
Disassemble dryer. Replaced element assembly. Re assembled dryer. Unit runs and heats.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Hickory, NC
- Parts Used:
- 532177968
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
Lound deck noise when mower put into motion
Parked mower on level concrete drive, laid on cardboard. Lowered mower deck all the way. Sparayed some WD40 on nut/bolt on top of old pulley. Since it is a carriage type bolt, placed 5/8" boxed end wrench over self locking nut on top of old pulley. Using some force from 3lb mallet to break nut free (hitting against wrench body), the nut came off easy as did broken pulley/bearing inside. Installed new pulley assembly, re-tightened nut on bolt. Checked after first mowing just to be certain pulley was in place and locking nut tight.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from BINGHAMTON, NY
- Parts Used:
- 532121749
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front wheels, too much end play
Shimmed the wheels out on axle.. No more slop.
Was this instruction helpful to you?
Thank you for voting!