Models
>
LT2742A2-96041025200
LT2742A2-96041025200 (2013-08) Jonsered Lawn Tractor
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Jul 23
$6.55
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part...
In Stock
Order now and your part arrives by Jul 23
This is an OEM axle cap for lawn tractors and is sold individually. It stops debris from getting into the wheel hub and axle. This axle cap is prone to wear and tear and should be replaced when it is ...
In Stock
Order now and your part arrives by Jul 23
$6.55
This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to ...
In Stock
Order now and your part arrives by Jul 23
$12.05
This is an OEM bolt and washer assembly, designed to hold the lawnmower blade to the spindle shaft. This threaded bolt has a curved rounded head and measures approximately 7/16-inches by 2-inches. If ...
In Stock
Order now and your part arrives by Jul 23
$26.35
This replacement blade is supplied directly from the original equipment manufacturer for use with Craftsman riding lawn mowers and garden tractors. It is secured under the deck to cut the grass, over ...
In Stock
Order now and your part arrives by Jul 23
This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most mod...
In Stock
Order now and your part arrives by Jul 23
This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are ...
In Stock
Order now and your part arrives by Jul 23
This is a Genuine Manufacturer Approved replacement washer used on lawn and garden equipment. This part is made out of Metal and is Sold Individually. Washer helps to distribute the pressure evenly ov...
In Stock
Order now and your part arrives by Jul 23
$18.65
This is a single mandrel ball bearing for a mower. It is sold individually, however it is a good idea to have a couple of these on hand. This bearing is located on top of the shaft, which is part of t...
In Stock
Order now and your part arrives by Jul 23
$34.27
It is a genuine OEM sourced part is specially designed for riding lawn mowers and garden tractors. The solenoid acts like an electromagnetic switch, it engages and routes the battery electrical supply...
In Stock
Order now and your part arrives by Jul 23
$31.53
This ignition switch has been sourced directly from the original manufacturer and is sold individually (key sold separately). The ignition switch is also sometimes referred to as a starter switch and ...
In Stock
Order now and your part arrives by Jul 23
Common Problems and Symptoms for LT2742A2-96041025200
Viewing 2 of 2Drive system does not work
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat
... Read more
other side.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trace from LISLE, IL
- Parts Used:
- 532138971
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Needed to replace the bent blades on my riding mower.
- Made the mower safe to work on the blades (remove spark plug wires, etc.)
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact drive ... Read more r, ..... and you know the rest.
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact drive ... Read more r, ..... and you know the rest.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from EDINBURG, VA
- Parts Used:
- 538691001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Broken weld on right axle
Removed wheel (used strong magnet to catch the keeper)
Removed axle assembly from its mounting tube
(used strong magnet again to prevent keeper lose)
Installed replacement axle (again with the magnet)
Lubricated with 90 SAE
Re-installed the wheel (used magnet again to hold the keeper.
Mowed the lawn.
Removed axle assembly from its mounting tube
(used strong magnet again to prevent keeper lose)
Installed replacement axle (again with the magnet)
Lubricated with 90 SAE
Re-installed the wheel (used magnet again to hold the keeper.
Mowed the lawn.
Was this instruction helpful to you?
Thank you for voting!