20959 (400000000-402099999) Toro Lawn Mower - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donald from MARION, IA
- Parts Used:
- 119-2379
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
drive cable broke
removed the broken cable and installed the new cable,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from PRINCETON, MN
- Parts Used:
- 144-6431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
trailing shield had broken off the mower, rendering bag useless.
Removed the wheels, attached the shield and replace wheels. Easy-peesy!
Was this instruction helpful to you?
Thank you for voting!
Transmission quit working.
Replaced the drive belt (didn’t fix), inspected wheels and gears, didn’t notice anything wrong. Tried to spin transmission with wheels elevated and wouldn’t spin. Assumed transmission was bad.
Removed bolts from belt cover and removed belt. Took wheels off being careful to remove and save washers and snap rings. Once wheels were removed transmission (with axel) slid off pretty easy. Replaced with new one and reinstalled washers and snap rings. Put wheels back on and took outside to test it. It worked for a few minutes then froze up. Took wheels back off and found the washer and snap ring on the left side came off the axel. Replaced snap rings and washers then reinstalled. Worked perfect after that. Bottom line, I highly recommend replacing the snap rings with new ones.
Removed bolts from belt cover and removed belt. Took wheels off being careful to remove and save washers and snap rings. Once wheels were removed transmission (with axel) slid off pretty easy. Replaced with new one and reinstalled washers and snap rings. Put wheels back on and took outside to test it. It worked for a few minutes then froze up. Took wheels back off and found the washer and snap ring on the left side came off the axel. Replaced snap rings and washers then reinstalled. Worked perfect after that. Bottom line, I highly recommend replacing the snap rings with new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jo from SAINT LOUIS, MO
- Parts Used:
- 112-8818
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Replaced cable brake
Everything went very easy and was done in no time. After I put on new part, mower started right up.
Was this instruction helpful to you?
Thank you for voting!
The hub that the mower blade mounts to was broken
The hub that the mower blade mounts to was brokenPut the new Harbonne played and played securing flange bolted it up
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from YARDLEY, PA
- Parts Used:
- 105-1809
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Was this instruction helpful to you?
Thank you for voting!