JE1860BH - Instructions

Removed screws holding outer shell. Pushed in door handle to identify faulty switch. Ordered part. Pryed switch out with screw driver and unplugged. reinstalled new switch. Presto. BUT... I did NOT use both hands while working on the microwave. I did not release the energy from the capacitor or whatever holds the killer amperage even when unplugged. It would be advisable to do this first. I did not because it seemed complicated, so I was EXTREMELY CAREFUL about not touching anything else inside the unit. I used one hand only so if I did touch something I would not get juiced through the chest. It was a piece of cake repair, but I would not go deeper without doing the discharge routine.

The turntable made a clicking noise, sometimes turned in the wrong direction, and wouldn't turn when there was any weight on the plate. Nothing appeared broken in the 3 spoked thing on whcih the plate sits. I replaced the motor, but this did not fix the problem; everything works fine until I put on the plate or any food on the plate. I now suspect that the wheels of the 3 spoked thing have worn down. They have flat spots on them. They don't turn when the motor turns, but drag. I suspect that this drag was what striped my first motor. I will next replace the 3-spoked thing.

Removed chassis cover, traced power (hot good through fuse), neutral was interrupted though at the flame sensor. Replaced flame sensor. Replaced chassis cover, microwave works.

Turntable in the microwave stopped turning.

Had to remove outer cover (special screws involved). Found the correct part at PartSelect.Com and it arrived 3 days later as promissed.

This oven has diffcult electrical connections at switch to get disconnected. I found it easier with the sw loose and in hand so that the connectors can be released with a small screwdriver.

One has to this in order to test the part wirh an ohm meter. I found the sw did not close but remained open and thus caused the oven not to function.

Removing interconnect switch is tricky but not difficult.

Outer cover replacement is not as easy as it should be, especially the sides.

All is well and working.

Microwaves are simple devices if you are know how to read and understand schemetic diagrams.

Watched a couple of repair videos on Youtube by searching for the model number. Found out what to do in order not to get shocked by the powerful capacitor.
Ordered the two switches (To be sure, I could have ordered a third switch as suggested in the videos.)
Bought a tamper-proof star bit to get the cover off. Followed the directions to replace the switches. - I broke the harness and had to use some super glue, but it's all good. I should have removed the harness instead of trying to get a switch out while it was still in place.
It's all back together, and the wife is happy!!

This was probably the easist repair ever. Turns out the shaft of rotating ring assembly that fits over the turntable motor was cracked, so the motor was unable to enage the ring assembly to move it around.

1. lift off (remove) the round glass tray

2. remove the old rotating ring assembly. There was a cracked plastic piece of it still on the motor shaft that I removed with a pair of pliers.

3. slide on the new rotating ring assembly - be careful of the orientation.

4. replace glass tray

unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......

One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.

1) Removed 4 screws securing the microwave to the cabinet.2) Slid microwave out, unplugged and placed on a work surface that allowed lower trim to hang over. 3a) Removed two screws and removed the cover on top of the oven. 3b) Unplugged high voltage plug from Magnatron. 4) Removed wires from overtemp fuse mounted to Magnatron. 5) Removed the four screws securing the Magnatron to the oven. 6) Removed Manatron. It's a tight fit, but can be done without removing anything else. 7) Replaced Magnatron. This is where I needed the magnetic part retrieval tool. The nature of a Magnatron is the use of strong magnets surrounding the tube. Getting the four screws back into place wasn't possible with just a normal magnetic screwdriver tip. I used the retrieval tool to position the screws back in place. Be sure to not initially tighten any screw completely, until they can be evenly tightened. This ensures correct compression/seating of the shielding material near the neck of the tube. 8) Reverse removal steps. Plugged in and tested microwave function on a cup of tap water. 9) Reinstated in cabinet and got a big thank you kiss from the wife!

First remove all screws holding on outer metal casing of microwave. Next remove the back and bottom metal pieces. You will then be able to pull aside the outer casing so you can access the door switches. Check each switch with an ohm meter in both the open position and with the switch closed. If the ohm meter reads the same in both the open and closed position, the switch is bad. Check the top switch first. Replace switch and reassemble. Cheap fix for a costly microwave. Great customer service at Parts Select!

Over the stove microwave installed in top cabinet row.
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover.
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.

The replacement part that I ordered must have been a "generic" part, although, it works fine, the rollers are slightly larger than my original, making my plate sit higher than it had. Not a problem, if you are CAREFUL when taking food in/out/cleaning. Plate is easier to get off track with this replacement roller guide!

Pretty simple but required buying a set of security bits (#68549) from Harbor Freight for $7.00 to remove the outer cover of my GE JES2051SNSS microwave. At first glance I thought the cover would remove by going towards the front of the microwave, but it ended up just needing a tug to the rear. I like this site because they have pictures of the exploded appliances that show what your getting into.

Removed the back plate, removed the old motor and re-attached the new motor and the back plate. Took about 5 minutes. Works great.
Lesson learned - DON'T let your spagetti boil over.