GI15NFRTS1 Whirlpool Ice Maker - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- guadalupe from RIALTO, CA
- Parts Used:
- W10124096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Motor sounded like a small little airplane under my fridge, very loud.
Unplugged the fridge first then took the bottom panel off with a 1/4 inch nut driver. Disconnected the wiring & used my ratchet to reach the 3 screws that held the motor. Took me longer to clean the bottom of the fridge then the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Archibald from WOODBINE, MD
- Parts Used:
- W11179302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
semi-annual cleaning of the ice-maker
bought 4 bottles for use this year and next. strongly recommend the product if you have an ice machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guy from SURFSIDE BCH, SC
- Parts Used:
- W11566405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Disherwasher would not start
Found fault with recirculating pump. Found hot spot on pump circuit board . Replaced pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BLACKLICK, OH
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
loud griding noise
stopped the fan and noise stopped ordered fan motor and fan with interface cable. Using 1/4 inch nut driver to remove screws from motor bracket installed new motor and runs like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from BULLHEAD CITY, AZ
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Noisy condenser fan
I suggest following video supplied with order confirmation perfect fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from RICHMOND, VA
- Parts Used:
- WPW10217917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Valve needed replacement - ice had become very thin
Just install the new valve by reversing the process of removing the old valve. Only possible nance is with the quick release hose fittings - the collar is pushed down to release the hose. Also, be sure to FULLY reinsert the hose in the new valve. Best to twist the hose a bit when inserting so it goes through the o-ring inside the valve. If not fully inserted, it will leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from NORMAN, OK
- Parts Used:
- WP2313637
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broken ice cutter grid
Unplugged the unit. Removed 2 screws to remove front cover to access the cutter grid.removed 2 screws to the cutter grid, unsnapped power connector and removed broken grid. Slid new grid in place, reconnected power connector, replaced screws, plugged in ice maker and slid back in place. Very easy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from WINTER HAVEN, FL
- Parts Used:
- 4387020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice cutting grid wire broke into.
Removed broke wire and replaced new wire. Use gloves to pull the wire tight. That's very important.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Huntsville, AL
- Parts Used:
- W11566407, WPW10548509, W11566405
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
One of the circulation pumps was going bad and making a loud noise.
I replaced the two pumps, since both were the same design...figuring if one went bad then the other would soon go bad...and then I also replace the water level sensor. All had quick connect plugs. The time is just taking apart the various pieces, cleaning, installing the new pumps and sensor, then reassembling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Atlee from Jupiter, FL
- Parts Used:
- WP2149705
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broken light switch
Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from palm beach gardens, FL
- Parts Used:
- WP179051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
range handle fell off and screw got lost
It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindey from Austin, TX
- Parts Used:
- WPW10217917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freeze ruptured inlet valve
Simple to replace. Next fall I will be sure to drain the outdoor icemake and shut it down for the winter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barton from Ringgold, GA
- Parts Used:
- WPW10217917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
leaking water inlet valve
Received replacement valve ~ 3 days, easily replaced in less than 15min, works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- otis from frenchburg, KY
- Parts Used:
- WPW10217917
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
water leaking from water control board.
After turning off water to icemaker, defective control removed (two screws) and new unit installed.Worked perfectly.I was totally amazed when I ordered the part thursday afternoon and it arrived fridaY morning.Total time out of operation less than 24 hours.Wonderful results.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALAN from KENNETT, MO
- Parts Used:
- WP2313637
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
macnine was producing ice but would not cut into cubes
remove the front cover by removing two screws. then remove two screws with a nut driver on each side. unplug the wireing harness from the top of the unit (may need pliers for this) the pull the unit out. then slide the new unit in, connect the wireing harness, install two side screws, and install the front cover and wham you will have ice in about 30 minutes. thanks parts select. you were very easy to deal with
Was this instruction helpful to you?
Thank you for voting!