EC515WWV0 Whirlpool Ice Maker - Instructions

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Removed two thumb screws holding old cutter in place, Replaced old cutter with replacement part the same way I removed the old cutter. Problem solved.

Very simple fix, remove 3 screws, two connectors to the old switch

We pushed the water return hose up from the bottom of the freezer door then we cut the water hose off then we taped the new water hose to the old one using electrical tape then we pulled and pushed at the same time and ran it back down through the door, be careful when you get to the bottom of the door it might stick a little going through the door , on my first try the tape came off without the new hose coming through. Just run the old one back up through the door and re tape it and try again. The connection at the bottom is just a pull out and push in connection and it won't leak after you push it in.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

At the top of the unit is the grid-cutter, to remove, I unscrewed the two turn screws (usually can do by hand but mine were a little tight so I used pliers to turn them). I slid the unit out and disconnected the power supply and light switch. I removed the plastic cover on the front and put it on the new grid cutter, lining up the light between the plastic and the edge of the grid. Slid the cover back on and then slide the grid cutter back into place. Hand turning the two screws and it was making ice in no time.
I saved more than $200 doing it myself!!!

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Removed screw that held nozzle on. Pulled old line out far enough to cut off broken nozzle. Attached new line with threaded bolt and clear packing tape. Pulled old line out bottom of door until new line came thru. Removed tape and bolt. Attached new line to water supply. Attached new nozzle with screw. Checked for water leaks. Job complete!

replaced relay switch
when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some

I took the front access panel off by unscrewing the 2 philips screws under the water dispenser tray. The plastic trim piece lifts straight up. The assembly that holds the electronics to operate the ice dispenser and water dispenser is held to the door by two 1/4 hex head screws. You pull that up and out of the way. Then take the metal bracket off that holds the water nozzle to the door. There is a black water supply line that runs down the door and out the hole in the center of the left bottom hinge. (You’ll have to pull off the kick plate at the bottom of the refrigerator to access the connection) It is connected to a compression fitting that attaches to a larger white water supply that runs through the inside of the refrigerator. Feed the new black supply line down through the door (up top) and fish it through until it stops. It most likely will not poke through the hole in the hinge. I took a scratch awl to center the new hose to enable it to poke through the hole in the hinge. Reconnect the compression fitting, put the kick plate back in place, put the electronics back in place as well as the plastic trim piece that goes around the dispenser itself. Sit back, enjoy a glass or water and pat yourself on the back for saving yourself a $100 service call.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!