UNVIM98 Maytag Ice Maker - Instructions

Tested water valve by disconnecting power and adding 110VAC to valve to be certain the valve worked before ordering new ice maker. Rather than guessing on the part of the ice maker that was defective I ordered a new ice maker complete for a few doorars more and that fixed the problem.

After turning off the water to the fridge, I removed the 3 screws holding the icemaker, and unhooked the wire harness. I just reversed the process to reinstall and it took about 20 minutes, and we had a bin full of ice the next day.

I first removed the door, very easy to do, then removed one screw that held the icemaker in place. I then unplugged the electricity to the frig, slid the unit out and disconnected the electrical harness. Luckily the harness on the new icemaker matched up with the original plugin on the frig so it wasn't necessary to change the wiring on the new part. I simply slid the new icemaker in plugged it in put the retaining screw in, the door on, plugged the frig in and started makinmg ice. Couldn't have been easier.

Turned off power and water, removed 2 screws on the bottom, loosened 2 screws on the top, pulled ice maker out a couple inches so I could disconnect wires, and removed old ice maker. I cut the slot in the back of new ice maker for the water line with pocket knife and installed the new unit. Took less the 30 minutes.

three screws and a plug in and it was done!

The icemaker was an exact duplicate of the one in my refrigerator. I installed the correct shutoff bar on the icemaker and removed the tab for the water fill spout. After pulling the power cord I loosened the two top screws with a nutdriver and removed the bottom screw. I pulled the icemaker from the rear wall, away from the fill spout, and disconnected the wire harness. Installation was just the reverse of the removal.

I removed one screw from lower portion of unit and loosened 2 top screws. Lifted unit to slide off top screws and unplugged unit. Plugged in unit and positioned unit on 2 top screws. Installed bottom screw and tightened top 2 screws. Repair complete.

added lowering clips to brackets, plugged it in,
hung on sidewall. Plug in power, turned water on,
had ice in an hour. The written directions could be a little more detailed..I am very satisfied with the ease of installation.

I ordered the replacement ice maker on a Saturday, received it on the next Tuesday, and in stalled it in a little over 15 minutes. Very quick, very easy. Partselect.com was easy to use and exceeded my expectations on every issue. Thanks.

Parts arrived amazingly fast. Replaced top ice maker and bottom water control valve[which was probably the source of my problem all along] in about an hour. The online installation video's were a big help. Thanks.

replaced the element as described. it worked for 2 cycles and flooded the capture tray. I thought it may be an issue with the water supply line so I replace it and insured it was getting a good feed.
I have now shut the unit down and restating it . thank you for your concern. Any tips would be appreciated.

Removed old ice maker and replaced it with the new one, took 20minutes and existing plug worked so I didnt have to use an adapter. Been 36 hours and it makes ice fine but has only dumped 3 or 4 times, hope it gets better. I dont know what else to do to it. Proceedure was easy and quick./

I looked up the model# of my kenmore for repairs and partselect.com came up. I searched for the icemaker, wondering if I was even going to be able to figure it out. I was pleasantly surprise that when I found the part there was also a video on how to do the repair. I watched the video, ordered the part and when it came, the repair was a piece of cake.

Replaced with a new unit that fit perfectly in place of an old one. Took about 20 minutes.

Due to the fact the part I needed would cost more than half a new ice maker I decided on a new one. The instructional was great confidence builder. The only problem I had was the plug to the ice maker was attached to the side of the refrigerator and I had to disconnect the ice maker at the plug under the front cover and use the old plug. Not a big deal because the video showed me how to do that.
I received the ice maker within 30 hours of order which was amazing! Its been making ice like new.