10689582706 Kenmore Ice Maker - Instructions

diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well

I removed the 2 screws on each side of the grid and disconnected the electrical plugs attached to the grid. I slid the broken unit out. I then carefully slid the new unit in making sure not to pinch any of the electrical wires. I replaced the mounting screws, plugged the 3 connectors back into place and turned the ice maker back on. I had ice cubes within a couple of hours

I removed the cutter grid and unplugged the light bulb and wire heating plug ins. I slid the front cover plate off the cutting grid and loosened the screws on the front of the cutter grid and unthreaded the broken, top grid wire, leaving the bottom wire in place as it was in tact.
I then threaded the new wire through the cutting grid frame starting in the center and threading right and then left. While the threading was not difficult, the wire was easily kinked. The process up to this point was only 15 minutes or so.

Once it was completely threaded, I worked for a couple of hours trying to smooth and straighten the wire so that is was somewhat taut and straight enough to create symetrical ice cubes.
My frustration came in pulling on the wire from the center point to each outside ending point where it was to be wrapped around the screw and the screw tightened back down. The wire was fragile enough that it would break, by the time I was finished I barely had enough wire left to touch the screw let alone hook around the screw.
After 3 or four days of successful opperation, the grid quit cutting again. As I took it apart, it was obvious that the weight of the ice was enough to pull the wire, that was already too short, away from the screw. I refastened it again, but think it is unlikely to hold.
If it won't hold, I would be hard pressed to purchase another wire. I may bite the bullet and purchase the entire grid mechanism with the wires already installed. Even though the cost of the entire grid mechanism is $200 more than the purchase of another wire, it may well be worth the ease of installation!

Took the two pumps tested them with 12 volt Battery. one pump didn't work. Looked up part nomber on Google and it lead me to this Co.

First I removed the cutter grid assembly by removing two screws. Also disconnect the wire that powers the grid. Once on the bench, simply remove the broken cutter wire. String in the new wire, starting at one end and working back and forth to the other end. Tighten the terminal screw on the first end, and then "strum" the wires, one at a times, pulling the wires taught. Pull the excess wire thru the second terminal, until all wires are taught, with equal tension. Tighten the second terminal screw, and cut off excess wire at both ends. Re-assemble cutter grid into Ice Maker.
Problem solved!

Removed ice scoop and holder. Remove front cover and pump bracket. Replaced pump and replaced covers. Started up and working well.

remove tray from icemaker by removing 2 screws and disconnecting 2 electrical connectiona. Remove broken wire and restring new wire. Reinstall tray.

I called a repairman to come out and he said it would cost $320 dollars for the repair. So I bought the part and spent $85 dollars and about 25 minutes to repair it myself

Removed the grid. Removed the existing top to bottom wire. Restrung the grid with the new wire. Then, it cut ice just fine-better than new. Note: wire provided is only sufficient to rewire side to side or top to bottom, not both. If you need to do both, you'll need 2. Yes, lots of money for a few feet of wire.

Took off several plastic covers to gain better accessibility to the sensor. Had to pull out the whole support piece to get at the part. Took out the old sensor, cleaned the unit as best as possible, then installed the replacement. Turned on the power to the unit and reinstalled all the parts I took out for better viewing and accessibility. Started up the unit and it is slowly building ice, which I will remove and dispose of to start getting clean ice.

The post I read said start at the middle and work your way out towards the left and right. This was incorrect. All I did was secure one end to the torx screw and tighten it down. I then slowly pulled the wire as tight as I could around each insulator, going slow so as to not kink the wire (very easy to do). Once I was at the other torx screw I used a pair of linesman plyers to gently tug each wire tighter, I needed an extra pair of hands to hold the grid down. Once everything was tight I wrapped the last torx screw and tightened. Here's what no one is saying, you will not get the wire as tight as it originally was but that's ok. After I got everything reinstalled the ice maker is making ice like a champ.

removed broken wire, replaced with new wire and screwed the 6 tensions screws to tighten the grid wire.

Replaced the assy. But, I would have been happier if you sold just the wires. I could have replaced the wires at a much lower cost and may have taken less than an hour to replace the wires.Still happy - the ice maker works.

We had the coldest winter in 114 years in north Texas (must be global warming...) and our outdoor kitchen ice maker value assembly frozen and cracked.

1) Remove bottom panel screws using nut driver
2) Remove door screws
3) Unhook two power connectors from value assembly
4) Release water supply quick connects
5) Replace value
6) Re-install door - this is a a little tricky there is a spring on each side which slows the door when opening and this pulls the door down which means the screw are not properly aligned by default. You basically have to pull the door up( a second set of hands help) and attach the screws and then let it go.

The repair was fairly easy. Take out screws and lift top of ice maker but do not take off. Having 2 people to do this helps. Clean all parts with calcium deposits. Replace all moldy or broken parts. Some parts are harder to replace. The back screw of the pump is difficult to install. Use a magnetic screw driver for help holding the screw. We used a little wax to keep the screw on the driver. The ice maker works better than it has in 2 years.