79577579600 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ross from Murphy, TX
- Parts Used:
- 4580JA3042A, 4975JA2028A, 1SZZJA3011B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken roller wheel attachment point
The vegetable bins at the bottom of the refigerator weren't sliding smoothly, as the two outlying rollers had snapped off the large plastic frame that houses said bins. Unclipped/unsnapped all the covers and glass shelving and remaining rollers attached to the frame and reinstalled them on the new frame. The only tough part was removing/installing a couple of large transpaent pieces of plastic that sit directly under the glass shelf. I'm not sure what their function is, except perhaps to look nice. But I had to pull the frame out with surprising force to snap the pieces in and out. Had to use a screwdriver for leverage and was afraid I was going to crack the frame. There must be a trick to it, because I'm a strong guy and it was still hard for me to do; there must be an easier way. Nevertheless I got them in ok, and bins pull out easily again. I was impressed when comparing the old frame to the new one, btw, as the new one's roller-attachment point is far sturdier than the old one. Obviously this was a weak point that has been well-addressed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G.J. from WHITE BIRD, ID
- Parts Used:
- 6600JB3007E, 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights in upper refrigerator would not turn off with doors closed
replaced melted light covers, replaced switches, and found another problem with power circuit board relay, on order now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cedric from Milwaukee, WI
- Parts Used:
- AAP73871501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door
Simple replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from Raleigh, NC
- Parts Used:
- 4975JA2028A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Guide assembly rails
Very easy just took old out and put in the new ones. Took less then 2 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carmine from elk grove, CA
- Parts Used:
- 5027JJ2012D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shelf broke
Replaced rails and glass top. Thanks for the quick shipping and cheapest price
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Vero Beach, FL
- Parts Used:
- 6600JB3007E, 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights Stayed on Melted Light cover
Replaces door switches - removed screw from door hinge cover, lifted cover and removed switch. Plugged in new switch and reversed process. Removed screws from light bracket. Attached new frame to slots in roof and used screws to attach. Clipped on light cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Troutdale, OR
- Parts Used:
- 6600JB3007E, 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the lights inside the frig weren't shutting off
the lights melted the lamp case and cover. I determined it was the switch ,but there was 2 of them . I replaced both . I used a screw driver to pry the covers off the switches which are on the top of the unit .Then I press the tabs on the switch and pulled it out. Slip the wire connect off. slip the wire connect on new switch press it in till the tabs snap in ,put covers back on. the lamp base and cover had two screws holding them, pull the screws slip the old melted base and cover. snap the new base and cover in and put the screws in done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Abilene, TX
- Parts Used:
- 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lamp cover and case had melted
I removed the old lamp cover and case. Discovered that the last repair person had not re installed it correctly so the case had melted from the bulbs. I Removed the screws that was supposed to hold it up, assembled the case and cover, inserted the screws and anchored them in where they belong. Problem solved!
Was this instruction helpful to you?
Thank you for voting!