79577579600 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from PENNSVILLE, NJ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from CASA GRANDE, AZ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door slight switch failed
Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from CURWENSVILLE, PA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door light switch, 3rd one I have replaced in 6 years made in China.
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from HILLSDALE, MI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace switch
Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TONAWANDA, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from YORKTOWN, VA
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lower ice maker water feed froze and caused leak. Needed new water valve.
Took pics of original install, removed old valve, water tubes & plugs. Installed new valve, reconnected electronic plugs, water tubes, turned water back on and all has been well since. Thank you for your timely delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from BETHPAGE, NY
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice Maker and Water dispenser stopped working
Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.
Super SImple/
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.
Super SImple/
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karyn from DURHAM, NH
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace the light switch for the refrigerator
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alma from Winterport, ME
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the light did not work when door was opened. At first it would flicker then off completely.
My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from TULLY, NY
- Parts Used:
- 6600JB3007E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Left door when opened the light wouldn’t come on. Checked the light, ok. Ordered push button switch
Removed the cover 2 screws
Squeezed the 2 side sleeves and removed
Snapped in new button, replaced the cover. Done
Squeezed the 2 side sleeves and removed
Snapped in new button, replaced the cover. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Goose Creek, SC
- Parts Used:
- 4430JJ2004B, 4430JJ2004A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Right door cam broken
Remove door seal and cam shaft (one piece). Remove broken cam by removing Philips head screw. Replace broken cam with new cam and reassemble. The actual repair took about 15 minutes however the majority of time was spent figuring out that the door seal and cam shaft had to be removed, no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from SPARKS, NV
- Parts Used:
- 5007JA3006R, 4970JA3011C, 4930JA3043A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice chute door would open ok, but would not close unless you stuck your finger up inside and closed it.
Found a LG parts video and followed each step. Simple except getting the end of rod into the solenoid arm. Took a few tries, but got it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from TORRANCE, CA
- Parts Used:
- AJU72992601
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Valve assembly leaked
The assembly sent is different than what is on the unit. The connectors do not match. We called and it seems you don’t have the correct part. The only part we have found will only connect the ice maker or the water. It will be a shame if I have to buy a new refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from HAGERSTOWN, MD
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator light had a short in it and would randomly work
Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from SEBASTIAN, FL
- Parts Used:
- AJU72992601
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Slow water for drinking
Just like on YouTube very easy to do
Was this instruction helpful to you?
Thank you for voting!