25329111990 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Glenn from CHAPPELL HILL, TX
- Parts Used:
- 5304507199
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Followed the instructions that were sent and repair was easy.
Followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wissam farhat from medley, FL
- Parts Used:
- 216514000
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
End cap for side door shelf broken
Both end caps were missing on the door side bottom metal shelf. succesfully installed no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from North Little Rock, AR
- Parts Used:
- 5304507199
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Warm out door gasket.
Had to lossen around 60 screws to allow for the old gasket to be removed. Then I began the process of inserting the new gasket by fitting it into the gasket channel opened when I loosened the 60 screws. I inserted the gasket a little at a time making sure it was properly fitted then I tightened that part and then do the next part until I finished replacing the gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from HILLSBORO, NH
- Parts Used:
- 297243800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I knockedoff the door light sensor when I dropped a frozen jug of ice
I removed the plate (recommend using a magnetic phillips head screw driver to remmove screws which are recessed). I removed the old part and pushed the new part through the hole and carefully reached in behindto attach the wires to the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andre from ANDERSON, SC
- Parts Used:
- 216594300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Freezer was not freezing.
I removed the compressor start relay and replaced it with the new part. Initially it did not work. When I checked my work, I had to tighten the connector on the new part. Once I made the correction, the freezer is freezing normally again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from ORLANDO, FL
- Parts Used:
- 5304507199
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door wouldn’t stay shut
Purchased gasket from parts plus installed it and door still won’t stay shut without duct tape plus the frost is building up really bad looking for another parts store to get problem fixed
Was this instruction helpful to you?
Thank you for voting!
Plastic shelf supports broken
Needed to remove both left and right broken (plastic) supports and reinsert the new parts. Not hard at all...worked like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John W from Gloucester, MA
- Parts Used:
- 297243800
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
broken light switch
Removed 2 screws holding front bottom vent grille. . Through opening behind grille found broken part of switch hanging on wires. Removed wires from switch and fed them out through hole for mounting switch, connected wire and pushed into place. The greatest difficulty encountered was my 82 year old knees.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricardo from VICTORVILLE, CA
- Parts Used:
- 297243800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door switch broke
Removed bottom cover , just two screws , slid old part through install hole and removed wires from old switch and installed on new switch. Installed new switch in same hole and pushed gently until it locked in place. Reinstalled bottom cover and done.
Was this instruction helpful to you?
Thank you for voting!