25329111990 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from RIXEYVILLE, VA
- Parts Used:
- 5304507199
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Gasket old and leaking
This freezer has many screws that hold the cover on the back of the door and assist clamping the edge of the gasket in place. Be sure to just loosen the screws 3/4 the way out, use a flat head screw driver to pry the cover from the door in case over time it is stuck to the door. The new gasket will come in a creative box trying not to kink the gasket itself, but there will be some distortion of the gasket when you get it. Put it in the sun or in hot water. I put it in my dryer for 10 minutes. Remove the old gasket, and start at the top of the door to replace the gasket. TIPS: If the screws are backed out enough, there should not be any problem sliding the back part of the gasket under the cover. When on the sides, do not pull the gasket down to make it easier to slide the gasket underneath the cover. This will distort and lengthen the gasket so it will not fit and thin it out so it will not function well. Once the gasket is in place, tighten the screws being sure to feel along the outside edge of the gasket for any bulging that would indicate that portion of the gasket is NOT under the cover properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SEVIERVILLE, TN
- Parts Used:
- 5304507199
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Frost inside freezer.. Old door gasket leaking.
Pretty straight forward. Loosen all screws "but do not remove" pry door panel from door just enough to slip gasket behind panel. Make sure gasket is seated properly around door.. Tighten all screws snug...
Gasket may not seal right away due to being kinked from packaging, use a little heat on gasket witth hairdryer and push something heavy against door over night. The gasket will straighten out over night.
Gasket may not seal right away due to being kinked from packaging, use a little heat on gasket witth hairdryer and push something heavy against door over night. The gasket will straighten out over night.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Gurnee, IL
- Parts Used:
- 216594300
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The compressor would not run.
I removed the cover, used a multimeter to test the compressor circuit, and found the compressor start relay to be defective.
Ordered a new one and installed it when it arrived.
Ordered a new one and installed it when it arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CARY, NC
- Parts Used:
- 5304507199
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer is 17 yrs old so needed a new gasket. The results were poor since the new gasket would not allow the door to seal.
Removed the numerous screws and took the door panel off. Cleaned and dried it. Replaced the insulation and hung the penal with 2 screws at the top and sides. Started to fit the gasket under the edge of the panel and put on the screws as I went across the top then down the sides finishing across the bottom. Perfect fit but could not get the door to seal at all. Went out and bought a new freezer(did I say it was 17 yrs old?!?!).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherman from Tuttle, OK
- Parts Used:
- 216594300
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Compressor was short cycling
Removed the cowling with a square drive screw driver, removed the spring clip from the cover of the compressor controls with a screw driver, pulled off the old compressor start relay and replaced it with the new part. Since other problems could have caused the compressor to short cycle this was a "replace the part and hope it would work" since that would be the most common reason and it was not a very expensive part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from Hallettsville, TX
- Parts Used:
- 5304507199
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Gasket shipped in box, could never get wrinkles out, freezer leak, ice formed on for and freezer,. Could have saved $150.00 + by not trying gasket.
Purchased new freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Conway, SC
- Parts Used:
- 5304507199
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Hard to get under metal strip.
Took out screws completely then had to wedge gasket underneath. Gasket comes a little tangled in box should remove immediately and keep at room temp till ready to use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from LAKELAND, FL
- Parts Used:
- 5304507199
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Freezer seal was leaking
Remove door remove old gasket, put new seal in dryer for 10 minutes to help it shape better then install new gasket with about 50 screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from CEDARTOWN, GA
- Parts Used:
- 216594300
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Freezer would not run ... replace the compressor start relay which fixed the problem
Pulled out the freezer. Unplugged. No freezer back cover was there. The compressor start relay was in a plastic encasement attached to the compressor - wires led me to it. Removed the solid metal spring with a screwdriver and removed the plastic cover. Tried to pull out the defective relay but the freezer was so old I needed a pliers to remove it. When I put pressure on the old relay with the pliers the relay broke and came off in pieces. I then removed the wires from the broken parts and put them on the new relay. I pushed the new relay onto the 2 pins then replaced the cover and spring. After plugging the freezer in the problem was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from Jamestown, NY
- Parts Used:
- 5304507199
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
freezer not cold
took door of removed gasket replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arlee from HOUSTON, TX
- Parts Used:
- 297243800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Pushbutton light switch failed.
Needed a Phillips head screwdriver to remove bottom plate (kick panel). UNPLUGGED FREEZER. Removed plate pulled switch out through the mounting hole and unhooked the two electric wires. Placed wires on new switch, pushed wires back through the hole and seated the switch. Plugged in the freezer and opened the door - magic, the light came on. Replaced the front kick panel (hardest part was to line up the plate holes with the holes in the mounting bracket).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wissam farhat from medley, FL
- Parts Used:
- 216514000
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
End cap for side door shelf broken
Both end caps were missing on the door side bottom metal shelf. succesfully installed no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from LISLE, IL
- Parts Used:
- 216502600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
While defrosting freezer tossed the drain plug with ice and water into the sewer system.
Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from CHAPPELL HILL, TX
- Parts Used:
- 5304507199
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Followed the instructions that were sent and repair was easy.
Followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from HILLSBORO, NH
- Parts Used:
- 297243800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I knockedoff the door light sensor when I dropped a frozen jug of ice
I removed the plate (recommend using a magnetic phillips head screw driver to remmove screws which are recessed). I removed the old part and pushed the new part through the hole and carefully reached in behindto attach the wires to the new part.
Was this instruction helpful to you?
Thank you for voting!