1985818101 Kenmore Freezer - Instructions

First let me commend PartSelect for their incredibly fast shipping. Ordered on a Thursday and it arrived on Friday!!

The repair itself was fast and easy and let me add I had never worked on a washing machine before.

1)Unplugged power cord from the wall.
2)Turned off hot and cold water at the shutoff valves.
3)Disconnected water lines leading to the washer.
4)Removed 3 screws holding the bracket assembly on the washer.
5)Removed bracket and pulled water inlet valve out a few inches.
6)Held new inlet valve in same orientation as the old one and then one by one removed the four electrical wires from the old solenoids and attached them to the corresponding place on the new inlet valve.
7)Put inlet valve back in place, attached bracket, and secured it with the 3 screws.
8)Attached water lines to inlet valve and plugged power cord back in.
9)Turned water back on at shutoff valve and checked for leaks.

I washed a load of clothes after the repair and am happy to report that the hot water now runs in as fast as it did when the machine was new. This washer may be 30 years old but I think the old gal's got some life left in her yet.

Removed old part, installed new part. tested machine. worked fine.

Washer is enclosed in a walled partition. I spent more time moving the washer out so I could get to the back of the machine. Due to Maytag's design of a removal sheet metal panel holding the valve the entire water valve replacement was performed outside of the machine. The replacement valve was an exact duplicate and made it a simple swap out. More time was spent removing inlet hoses and outlet hose then in actual valve replacement.

open top of washer
remove two screws that hold water inlet valve
disconnect four wires and hose;replace new water inlet valve and reversed operation
everything went well

Pushed machine out from wall; disconnected the supply hoses (after closing the valves at the wall); unplugged electrical cord; removed two wires from the solenoid connectors; removed two screws that secure valve assembly to backplane of machine. Installation of new assembly was the opposite procedure. We have private well, and silt was plugging the cold water side of valve. So, I also installed a large sediment filter behind the washer, so this will never happen again.

First I remove the hot & cold water hoses using an adjustable wrench. I then unscrew the panel that holds the water inlet valve using a nut driver. I then carefully pull out the panel, moving the harness wires out of the way, so that I can loosen the clamp holding the inside rubber tube. I remove the old water inlet valve from the panel by removing the 2 screws and then put the new one in. I then reconnect the rubber tube and tighten the clamp. I then screw back the panel and reconnect the hot & cold water hoses. It took me about 20 mins to complete the job.

First thing unpluged power cord from wall outlet, removed hot and cold water supply hoses.Then took out srew holding metal plate ,pulled plate out exposing valve, marked wires and diconnected.Pulled clamp and hose from valve.Pulled out valve and reinstalled new.Reconnected wires and hose.Installed screw to hold in place, reconnected hot and cold supply hoses.Plug unit back in. Job done.Washer works like new.

followed simple directions... no brainer.
just be careful - shut off water and unlug first.

First check that the screens are not plugged. There are fine screens in the mixing valve and at times you will find them in either end of the inlet hoses. Not a hard job if you can get to the back of the machine, just a few small screws, swap the wires to the new part and swap the outlet hose from the valve and screw it back together. Wife will think you are a wiz kid.

Removed hoses and inlet valve from washer, replaced inlet valve by attaching the electrical connectors, reattached new water lines, returned inlet valve to its place in rear of washer. Checked for leaks, washed a load of clothes, everything worked properly.

Disconnected the electric plug and removed the water hoses from the washer. Took off the old water inlet valve under a plate on the washer and hooked in the new one. As we dismantled each section of the valve hook-up we connected that area of the new valve to be sure we got it connected correctly.

Shut water off and unplugged. Used channel locks to remove hoses. Used nut driver to remove mounting plate. Disconnected electrical connections to solenoids. Broke one. Had to replace. Used nut driver to loosen fill hose. Rusty and broke. Cut hose. Used new clamp to secure fill hose to fill solenoids. Stripped and crimped on new connector and replaced electrical connections as they were removed. Reinstalled hoses and plugged in. Tested A-OK.

The most important part of my repair was watching the video that was sent to me with my order confirmation. After I viewed it, the rest was easy. The only hard part was moving the washer away from the wall!

I ordered the part. Watched the video and did the repair. I removed the cover plate on the washer, removing the screws. I then, removed the broken water inlet valve and replaced it with the new one. I placed the cover plate back onto the rear of the washer and "VOILE", it was done. I am a divorced mother of three, who has never attempted to do any type of home repairs, however, the way PartSelect has set up the website, it made it easy to determine what part I needed and provided me with a video which gave me step by step instructions on how to repair it. I even posted my victory on Facebook! Thanks PartSelect.

Because the washer was old, 27 years, I actually ordered a new machine but after doing so was able to get the old washer to pump out the water. It had overfilled and spilled water on the floor. The next time I ran the washer using "warm" setting the hot water inlet solenoid failure was evident. I checked voltage at the solenoid and it was getting power so figured I'd try ordering a $30 part. In a couple of days it showed up and after less than :30 minutes I had the washer running again. It would have taken less time but a screw stripped out and I had to locate a replacement. I'd definitely recommend PartSelect. Oh, we cancelled the replacement washer and figured the Maytag repairman could resume his slumber!