FFU20G9GW0 Frigidaire Freezer - Instructions

Purchased gasket from parts plus installed it and door still won’t stay shut without duct tape plus the frost is building up really bad looking for another parts store to get problem fixed

Brought replacement key works just like original I thought it would be metal from reviews but it was plastic and still works perfectly

It's easy to know how to use a key. I didn't have a difficult part, I didn't have the model # because I had lost my key and the model # is inside. I was able to find the energy saving paper that came with it but it had four model #'s. I called a couple places and no could me. I pulled up Part Select on line and just thought I would give them a try. I got a very nice person (Jeremy) He went thru every model that I had and three out of the four matched so he sent me a key and if it didn't work I could get my money back. I give him a A+ four taking that extra step, unlike the other places. Very satisfied!

Oh yea thanx to partselect it went great didnt get fisrtkey but when got the second key it worked great thanx partselect

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

Notice ice build up on the panel in front of the evaporator coil. Unplugged freezer and removed evaporator panel. Plugged unit back in and checked fan, coil "snap switch" and heater element, all seemed to check out good. Found defrost timer stuck in the freeze position, causing frost to accumulate over the evaporator. Manually rotated defrost timer to the 30min defrost cycle and system went into defrost. Ordered defrost timer and installed (part arrived in 3 days). Freezer works great again. Too bad I ended up throwing 400 dollars worth of meat away. the fix was very simple. Will definitely use PartSelect again. Thank you.

Slipped off the top and bottom screw cover plates unscrewed the 4 retaining Phillips screws, removed the old handle and replaced it by reverse the procedure. The best part of the process was the amazing quick delivery and efficiency of Parts Select.

Took interior panel off and uncliped yhe termination switch and cliped the new one on the coil and connected the two wires very simple. The defrost timer was located in the rear of the unit on the right side at the bottom. Removed the 2 screws holding the bracket unpluged the timer and removed the timer. The new timer allready had a bracket so just plug in and install the 2 screws. Pluged the unit in and worked great make sure that the freezer is unpluged before changing any part

We really didn t need to do a repair, we just ordered a freezer key that we didn t have. I must say the shipping was fast we received it the next day. It was worth the shipping charge. We will be ordering again. Great service.

Ordered freezer key friday afternoon received it saturday afternoon. Fast service

The sliding shelf side rail is held by three philips head screws that tighten into nut inserts. No amount of tightening would keep two of the three screws tight. I found that the nut inserts which are plastic and insert into the side of the freezer would pull loose, probably from years of overloading the sliding shelf basket. Ordered two nut inserts from PartSelect. 1. Remove three screws to remove shelf slide side rail. 2. Remove nut inserts to be replaced with needle nose pliers or reinsert screw a couple of turns and pull nut insert out with pliers. 3. Insert new nut inserts, position side rail, and tighten screws. Replace sliding shelf/basket.

Upluged power pulled freezer out from wall removed the two screws that holds the defrost timer unpluged defrost timer pluged new timer in mounted new timer back with the two screws pluged freezer back in and job was complete. Freezer working fine.

Easy repair, snapped off two trim peices, loosened 4 screws and removed the old handle. Screwed the new handle on replaced the trim peices and was done.

Even though we did not have the model or part number I was able to easily locate the exact part because of your photo, dimensions and video instructions.

Removed three screws each side to remove old slides. Needed spacers under new slide so that drawer would stay on track. Cut old slide to make spacers and installed both slides in 15 mins.