FFU20G9GW0 Frigidaire Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Andre from ANDERSON, SC
- Parts Used:
- 216594300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Freezer was not freezing.
I removed the compressor start relay and replaced it with the new part. Initially it did not work. When I checked my work, I had to tighten the connector on the new part. Once I made the correction, the freezer is freezing normally again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- warren from Farmdale, OH
- Parts Used:
- 297013500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken drawer slide
removed old broken part, 3 screws, then installed new part.....done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SALLY from DICKINSON, TX
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door handle broken at screws
removed 4 screws-replaced handle-very easy-worked great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dylan from Celina, OH
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke at the attachment point on the door
removed two pieces of trim.....removed four screws of old handle.....replaced with new handle....replaced screws.....replaced trim pieces
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Salt Lake City, UT
- Parts Used:
- 297311201
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fridge door handle broke off, replaced it.
Very simple - removed the plates that cover the end of the handel, then removed the screws and the broken handle. There were four screws - did a top one, then a bottom one, then the other top and bottom one. Made sure they were on tight and put the covers back on. Really proud of myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edith from FORT WAYNE, IN
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broke off of the refrigerator
Was able to order the handle and screw it on the refrigerator using the screws from the original handle in about 10 to 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stirling from FORT WORTH, TX
- Parts Used:
- 5304518034
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Coils were freezing up. Defrost cycle not working
First unplug freezer, then disconnected wires from timer.
Removed 2 screws from bracket holding time to freezer.
Attached New part with screws. .The mounting bracket is now part of New time. Reattach wires.
I let coils defrost and then plugged it.
Removed 2 screws from bracket holding time to freezer.
Attached New part with screws. .The mounting bracket is now part of New time. Reattach wires.
I let coils defrost and then plugged it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Bowie, MD
- Parts Used:
- 297013500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Brackets for the food basket were broken and the basket alwaws fell off the track.
Removed the basket. Removed the two broken brackets (6 screws). Installed the two new brackets. Put the basket on the track. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from LEXINGTON, KY
- Parts Used:
- 297311201
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broke off
Four screws and slip on the covers! That's it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SWAMPSCOTT, MA
- Parts Used:
- 297311201
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle broke loose
Just screwed in the new handle. Must keep the original trim pieces that slide on the top and bottom, or order new ones if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from MENDON, MI
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door handle
remove cover plates slide off , exposes screws holding handle on to the door remove screws ( 4) 2on top 2 on bottom replace with new handle in reverse order of disassembly slide cover plates back on , job complete .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from HIXSON, TN
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken handle
Took off 4 screws and replaced the handle. Took less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND FORKS, ND
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door handle broke (3rd one) poor design
replaced handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from MANLIUS, NY
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven not reaching temperature
Using the socket wrench, I removed the old element from the oven wall attached by two hexagonal screws. I then removed the electrical attachment to the oven using a Philips head screw driver. Replaced the element with the new one and reversed the process. The oven works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from Ayden, NC
- Parts Used:
- 216594300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer just quit working. I could turn thermostat off. Click ever few seconds would stop..I figured the thermostat was good compressor not starting
First unplug it and pull away from wall to gain access to the Rear of freezer.
From the rear of the freezer. You can clearly see the compressor.....I had to lay in the floor. Best way to see what your doing .
Attached to the side of the compressor
Is square cover over the start relay..it has a metal bail that retains the cover. Simply remove the strap with a flat blade screwdriver the cover can then be removed. A flashlight and screwdriver is all I needed
The switch body plugs onto the compressor with pins or blades. Mine broke in a few pieces by the time it was completely removed. The start switch has very tight connections so its a bit of a struggle to get it off. ..stick screw driver behind it and try pry evenly until its off..secure new switch on the pins and push it in ..there is one single wire attached to the start switch no confusion there.install cover and its retainer and its done..
From the rear of the freezer. You can clearly see the compressor.....I had to lay in the floor. Best way to see what your doing .
Attached to the side of the compressor
Is square cover over the start relay..it has a metal bail that retains the cover. Simply remove the strap with a flat blade screwdriver the cover can then be removed. A flashlight and screwdriver is all I needed
The switch body plugs onto the compressor with pins or blades. Mine broke in a few pieces by the time it was completely removed. The start switch has very tight connections so its a bit of a struggle to get it off. ..stick screw driver behind it and try pry evenly until its off..secure new switch on the pins and push it in ..there is one single wire attached to the start switch no confusion there.install cover and its retainer and its done..
Was this instruction helpful to you?
Thank you for voting!