YWED8800YW2 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROGER from MADISON, TN
- Parts Used:
- WPW10547292, WP8547157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken dryer belt and broken idler pulley wheel
Looked it up on YouTube and followed the video instructions. Repair went fine after I got the correct parts ordered from two different places before I got the correct parts. Parts Select was the only one that sent the correct parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from KENNETT, MO
- Parts Used:
- WP8577274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Shutting off and had to wait before could turn back on
Followed online video very easy and dryer works like new one....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from MARION, KY
- Parts Used:
- WPW10359272
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
Rollers making a noise.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from ETTERS, PA
- Parts Used:
- WP8544737
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
The fan wheel had a blade break off, my bad.
I went on the site and found the part I needed and then watched the video explaining how to dismantle, replace the part, and put the dryer back together. It was easy, especially with the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from BENZONIA, MI
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screen ripped
Dropped new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from CARY, NC
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rory from LEESBURG, VA
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Dryer kept throwing the E1 error indicating the thermistor needed replacement
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Anderson, IN
- Parts Used:
- WP3390719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dryer electrically dead
Unplugged power cord. Removed rear panel screws and panel . Removed the two wires connected to part. Removed two screws holding part and replaced all components in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from FRUITA, CO
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic retainer on catch was broken
Used screwdriver to remove old catch as shown via video from manufacture and snapped in new catch. Very easy to do and saved big bucks by doing myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from W TERRE HAUTE, IN
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Latch Replacement
Used a screwdriver to pry out the bottom of the latch then the top. Pulled old latch out, then snapped new one in. Super Simple fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Forrest from PARIS, TN
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door Catch broken
Took Putty Trowel and pried out top and bottom then pulled out with needle nose pliers, new part just pops back in (be sure flanges are on top and bottom not sides).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SCOTTSDALE, AZ
- Parts Used:
- W10120998
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Torn filter seal
Remove old filter, throw it away, replace with new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from HOPATCONG, NJ
- Parts Used:
- WP3390719
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Dryer would not start due to over heating
Followed the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from VILLA RICA, GA
- Parts Used:
- WP3390719
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dryer would power up but not run.
Removed front of dryer. Located thermal fuse, replaced blown thermal fuse. Reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from Marietta, GA
- Parts Used:
- 279973
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Dryer stopped heating
Determined via multimeter that either the thermostat or thermal fuse were not working, so ordered the kit (best value, contains both parts).Easiest access is from the rear, so removed rear panel and top of dryer (required) and also the vent tube since it was in the way. Unhooked wires from both parts, used socket to remove nuts holding each one on, put new ones in place, re-attached wires. Replaced vent tube, vacuumed entire inside of dryer (good idea). Put back/top back on and the dryer worked/heated perfectly immediately.
Was this instruction helpful to you?
Thank you for voting!