YWED8500DW4 Whirlpool Dryer - Instructions

pull the back off and replace the pulley.

Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.

Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck

first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.

I removed the metal piece which held the plastic "catch". There were no screws, squeeze to remove it. Then inserted the plastic part and re-inserted the metal part into the dryer door. Very simple. But even more pleasing was the easy ordering and the quick delivery of the part! Thank you so much!

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

The first thing I did was to watch the video from Part select on How to change thermostat cut off switch and the high limit thermostat fuse.I did not have a meter reader I just brought the thermostat cut off kit for about $ 32.00 dollars from part select and replace both part's and my dryer still was not getting hot so back to part select video's I looked up the video on replacing the heater element and I ordered one for about $ 97.00 with shipping I replaced it and put it back together and it worked it took just a few hours . I would like to give Avery special thank to part select for the video help and for having the parts for a great price again thank you so much.

Followed your video for replacing the Tension Pulley, Drum Belt and Drum Rollers. Models were not exact, but instructions were very clear and detailed enough for a "computer geek" to do the repair myself (with some help from my wonderful wife). Live in Ohio, parts came from Kentucky and I had them the next day! The dryer is almost 10 years old. Running great now. Thank You!

unplugged the dryer and removed collapsable vent then we laid it on its back. took off the lower front face with a screwdriver ( just inserted in upper margin and it popped off) then removed a couple of screws and put the new element in replaced the screws and we cleaned all the old dust and lint from in the cabinet and replaced the front face. no problems.

Removed front panel located hearter elemement houseing
removed screw securing houseing to dryer chasis, disconected wireing harness- be carefull here there are three lines two for the thermostat and one for the element- you only need to disconect the one nearest the front of the unit, reove the screw holding the element to the houseing it sits in and pull out. instalation is reverse the directions to remove

Removed the screws holding the front cover, Removed the screws holing the heating element bracket, pulled the heating element housing out, unplugged element and removed old element. Very easy to install. The exploded pictures on website really help.

First I unpluged the dryer from the electical power. I removed the 2 screws holding the bottom front panel. Then I saved a bit of time and effort. Instead of removing the bracket and pulling the whole unit out, I bent the metal plate in front of the heating element toward me. I unpluged the 2 wires from the plastic casing and removed the screw holding the heating element in place. Next I pulled out the old part and pluged in the new one then connected it in reverse order and bent the plate back up to protect the element. This was a very easy and inexpensive way to fix the dryer like new again. The hardest part was vacuuming and cleaning the bottom of the dryer. There was seven years of lint build up under there.

Pulled the back panel off with nut driver , reached in removed belt from pulley , disconnected the spring , removed the the 1 bolt holding the bracket .
Put the new one in , in reverse order . Very simple , maybe 15 minutes total . While back is off , shop vac out any lint !!

Lint can build up inside the dryer, and can cause a fire in EXTREME cases. If your model has a back panel that exposes the entire chute, this job is much easier. Unscrew the chute from the machine to remove it. Inspect and clean all the lint out, especially the bottom, next to the fan blower. The other version machine has a panel at the top that is welded on. Remove the two screws at the top corner of the rear bulkhead, where the chute is. Gently pull this inner panel away to free the top of the chute from the rear top panel. Then pull the chute down and out. Follow the reverse to complete the job.