YWED8500DW4 Whirlpool Dryer - Instructions

Replaced door catch on dryer door. Followed video on Whirlpool website and it took less than 10 minutes. The dryer works great.

Just follow the repair video, it was easy!

Followed online video very easy and dryer works like new one....

The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and remove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.

Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..

I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.

I just took the old element replaced with the new one i order from this site, I save some money was really easy so proud of my self...

Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.

Lubricated pulley wheel which temporary reduced noise. This verified what was making noise. Looked up the part on partselect.com and ordered it. Recieved idler pulley with bracket in just a few days.
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and removed old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

Unscrewed the inside part of the door from the outside door shell. Removed the broken pieces of the catch and replaced it with the new one. Screw the door back together. Did not need to remove the door from the dryer cabinet.

removed broken parts & snapped in new catch

Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.

Took back panel off, and it was really easy putting the new idler pulley in.

I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.