CEM2765FQ0 Whirlpool Dryer - Instructions

Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.

all that was required was to push the catch into the slot notools needed.

replaced dryer lint screen with new.

removed the rear panel to gain access to the internals of the dryer, removed the one screw that retains the fuse, out with the old and in with the new.
delivery of the part was 2 days sooner than expected.
could not have been a simpler process!

I first watched the helpful video on website. Un- plugged the dryer. I removed the back cover and tested the thermal fuse with the multi meter. Ordered the replacement part. Replaced the Thermal Fuse, and put the back cover back on. This was a very easy fix! It takes longer to remove the back cover of the dryer than it does to replace the fuse. While I had the back cover I used my air compressor to blow out any lint. This dryer is as good as new now. this site fast shipper, Great website.

This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.

Unplugged stove . Removed floor of oven . Easy . Removed the ignitor ,near back of stove under removed floor . .Left it in place to enable locating where wire came through back of stove . Pulled the stove away from wall . Removed back panel of stove . followed ignitor wire to its plug in position . Returned to the front of stove . Inserted new ignitor wire through back wall of stove . Went behind stove , pulled wire through enough to plug new ignitor into proper position . Put back panel onto stove . Pushed stove back against wall . Went back into oven to screw new ignitor into place . Replaced oven floor panels . Put cooking racks back in . Wife proceeded to bake once again .

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.

Just follow the repair video, it was easy!

Once again part select has come through for me. googled dryer won't start and a video on utube came up. typed my model number in on part select website and followed directions. was easy got part in three business days regular shipping. very pleased with this site.

I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.

Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.

I ordered this to repair my girlfriend's mother's dryer. But according to my luck, the day the part was to arrive, I suffered an small brain bleed that put me in the hospital for a couple of weeks. I had read the instructions and was able to explain it to my girlfriend who replaced it and got it all back going right!

Went on line and determined the problem was the thermal fuse. Removed the rear panel of the dryer, removed the leads from the thermal fuse, hooked them together and started the dryer. That confirmed the problemwas the existing fuse.Ordered the new thermal fuse, installed the fuse, hooked up the wires and it works finel Very simple fix. About a 10 year old dryer.

I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.