LER3622PQ3 Whirlpool Dryer - Instructions

Replacement fit perfectly.

When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked up the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.

Watch the video before I received the part. Made it very simple to replace and which screws to take out.

pop off the lid, replace the switch. (in meantime, while waiting for replacement switch to arrive, shorted switch wires together to fool dryer into thinking door was closed)

Watched video, followed instructions. Works perfect.

My dryer would not start or turn. I first moved the timer to midway between start and end of a cycle and could hear the timer ticking, likely eliminating the timer as the culprit. I next opened the door, manually pressed the door-closure switch and pressed START to see if the heating coil was heating without the drum turning to see if it might be a motor issue. After no heat, I unplugged the dryer and removed the vent hose by loosening the clamp and then removed the lower back cover using a socket and ratchet. Using a multimeter, I quickly found an open thermal fuse. I tested the remaining components to see if they also required replacement (coil, thermostat, high temp sensor) - all tested good. Took a chance and ordered the fuse alone instead of also purchasing replacement thermostat as many advise - if you have not replaced in a while, probably worth doing now. I have replaced mine within a year or two and chalked up the issue to my kids not clearing the vent, so I went without the new thermostat. Model number was found by opening the lid - parts arrived incredibly fast especially for being around the holidays. Replaced the fuse with ease - there is a notch in one end that holds the non-screw end in place so it's flush. Plugged the dryer back in, selected a cycle and confirmed the dryer started and heated as normal. I then had my son open the dryer door to confirm the drum stopped turning. HERE'S WHERE IT TAKES A TWIST: When the door was open, the heating coil continued to glow red hot (faulty timer??) I moved selector to end of cycle and the glow stopped. (timer's good) I then moved the selector mid-way between cycles with the dryer door open and WITHOUT PRESSING START and the coil again glowed red. Disconnected power, disconnected coil and using multimeter, checked from coil input to case ground (any bare metal) and found one side of the coil to be grounded. I was able to removed the heating coil and locate where the coil was touching the case. I shifted the coil back into place, checked with meter (no ground this time), reinstalled and tested with no problems. Reinstalled the back plate and vent hose. Finally, had conversation with the kiddos about being gentle when moving the dryer and all was well. The thermal fuse portion took 15 minutes from diagnosis to replacement. The overall process (due to the additional grounded heating coil) took 30-60. With any repair like this, I usually recommend visually verifying the heat cycles on and off by carefully running with the door open and holding the switch. This will help you determine if you may have an additional faulty part that made the first one fail. (Most likely, thermostat).

I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Performed current check to determine possible problem-then Able to go on line with partselect, extremely easy part description and selection, ordered, part arrived next day. Could not have went any better

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

all that was required was to push the catch into the slot notools needed.

Easy for a 87 year old.I just snapped the cover to the filter basket and then inserted the whole basket into the

Removed Back and found schematic. Found fuses on schamatic and parts inside dryer. Checked fuses and thermal fuses with an ohm meter and found one that was open. Went to Parts select and ordered part. Relpaced the part and dryer works like new.

I found the door switch in the upper right of the door opening was broken. This will not allow the dryer to turn on. The switch is held in by two phillips screws.I removed the screws holding it in place. Next open the door where the lint filter is and remove the two screws. Now at the front corners of the dryer on each side you will need to insert at tool to pop the clips.I used a door panel trim tool. Once you pop the clips lift up the top of the dryer. Next unplug the switch and remove it. Install the new switch through the hole install the switch screws drop the top back down and clip it, reinstall the screws at the lint filter. If this was your problem the dryer should turn on. This is a 15 min job!!!

Unplugged stove . Removed floor of oven . Easy . Removed the ignitor ,near back of stove under removed floor . .Left it in place to enable locating where wire came through back of stove . Pulled the stove away from wall . Removed back panel of stove . followed ignitor wire to its plug in position . Returned to the front of stove . Inserted new ignitor wire through back wall of stove . Went behind stove , pulled wire through enough to plug new ignitor into proper position . Put back panel onto stove . Pushed stove back against wall . Went back into oven to screw new ignitor into place . Replaced oven floor panels . Put cooking racks back in . Wife proceeded to bake once again .

Those 2 little parts I ordered
Door Switch Assembly
And
Thermal Fuse
I thought the Thermal Fuse was the main thing that caused the dryer to quit working, I was pissed lol, so I went ahead and installed the Door Switch Assembly, which hadn't work for quite awhile, and bingo it worked, oh my god I was so happy, and it was so easy to do!!!!