GEC9858EQ1 Whirlpool Dryer - Instructions

Just like the video, just followed the video
Thanks,

Removed the back of the dryer about 8 screws. Removed the Thermostat 250 F and replaced with new. Dries a load of clothes in one cycle on medium. Not bad for a 16 dollar part. I am a computer tech and I am used to taking computers a part but I think most people that are in anyway mechanically inclined and can look at a diagram could do this and save yourself a lot of money.

The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and remove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.

i took off the back of the drier and with a screw driver removed the 2 screws and put the new part on

After checking the temperature safeties, I replaced the Push-To-Start switch. This did not solve my problem, so I replaced the Timer Switch assembly, which did solve my problem. Both switches are very simple to replace. Unplug the dryer, use your nut driver to remove the 6 screws holding the back control cover. For the Start switch, remove the control knob, remove the 2 screws holding it it. Unplug the wires, turn the switch housing 1/4 turn clockwise, and remove it from the opening. Reverse the process to install the new switch. For the Timer Assembly, just a bit trickier. Remove the knob, remove the 2 screws holding the assembly. Unlike the Start switch, the Timer Assembly has multiple wires. Pull the old timer assembly out, and, one-by-one, move wires from the old Assembly to the new Assembly, being sure to land them on the proper post. Once you have done this, return the Assembly to the mounting hole. A very simple repair. Even though I spent $160 chasing the problem, I still came out cheaper than calling a repairman.

I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

I removed the back panel and tested the Thermal Fuse, the Thermostat and the Heating Element with a meter. The Thermal Fuse gave a bad reading. I proceeded to clean the dryer and lint pipe of all lent. I installed the new Thermal Fuse and put the back panel back on the dryer. The dryer worked for two loads of clothes and the Thermal Fuse blow again. I'm now at the end of my rope. I don't know what else to check and I can't continue to buy parts for only two loads. I guess I will have to invest in a new dryer.

Opened access door, noticed main power wire to heating element was partially melted. This was caused by a bad connection to the drying element, loose. Removed heating element assembly. Cut bad section of wire and added new connection. While doing this the thermostats plastic casing cap came off ! Probably due to exessive heat / resistance from the bad connection. This confirmed why there was no heat. Intalled new thermostat and and am now good to go !

Just change the timer as follow taking off one wire on the old timer and connect to the new one, and do the same thing for all of the wires.This way will be not confuse with the connections.

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Removed the screws replaced the belt and lubricated the wheels and that fixed my Knocking and it runs like when I first got it

Took, back cover out,but first i disconect the electricity,i give a fast look,looking for anything wrong and i saw a thermostar burn out in the element case,the bottom one,a thermostart
250 f. but a did a search in the internet,and found that when a bottom thermostart burn out, the top one had to be change,so i did a continuity text in the top one and was open ,i have it,a used one, change and connect the dryer to the Electrical outlet and (walac)it start the dryer,problem solve

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.