WED6200SW1 Whirlpool Dryer - Instructions

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

Take front panel off with 5/16 nut driver and reach in and get 3/8 socket to remove 1 bolt off and replace idler pulley

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

first, I read the other repair stories and used them as a guide.I checked to see if the heating element was broken. It was not. The Thermal Cut off Kit was the ticket for me. I replaced the three easy parts it contained. Repair time was 30 minutes tops that includes checking the heating element and removing and replacing all three possible culprits (of the Thermal Cut-off Kit). Thanks a million. Happy Ending!Oh by the way, my dryer now dries super fast(saving me a bundle)

unpluged the dryer, took off the back, followed instructions and was able to take of the problem on my own.

Our dryer quit heating and I feared that I would have to buy another one as I have never worked on a dryer. But figured I would go online and see what I could learn. Parts Select gave me the info that I needed.
Not being sure which part was bad I decided to start with the one time use Thermal fuse. When I noticed that it only cost 7 bucks and my wife had been complaining that the dryer had not been heating well for a while I figured I would go ahead and replace themostat. I ordered the thermal cut-off kit and replaced both parts. I put them on and plugged it back up and it is heating fine. I found the videos very helpful in showing how to do this.

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.

removed back of dryer. Pull electical connections, removed heating element. Inserted replacement element, attached electrical connections and attached dryer back. Done -easily done.

Dryer ran with no heat. Replaced the Thermal Fuse and when that didn't fix the problem discovered the element was burned. Easy fix except the F-disconnect fitting broke when I tried to remove it and male fitting on the heating element is 0.375 and all I could find were 0.250 F-disconnect fittings. I finally found a supplier who had a 0.375 fitting and the repair took 10 minutes after that. The online videos at PartSelect are excellent.

Unplug unit first.
Took the front cover off the front of dryer below the door.

As seen in video, All Good !

The online heating element replacement instructions were excellent. The back panel of the dryer was removed by unscrewing 9 screws. The difficulty arose in trying to remove the thermostat from the damaged heating element. My thermostat wasn't connected by screws (the thermostat in the online instructions was). It was much easier to follow the online instructions up until the thermostat removal section, and then remove the thermostat by first removing the heating element from the dryer (connected by two screws), and then using the needle head pliers to gently remove the pliable metal prong that holds the thermostat to the heating element. The metal prong is secured near the top of the thermostat. Once the metal prong is removed, use the pliers to carefully remove the prong that connects the thermostat to one of the two prongs at the bottom of the heating element. The thermostat and the flat wiring connected to the thermostat are one piece. The thermostat is connected to the heating element by the pliable metal prong and the delicate flat wiring attached to the bottom of the thermostat. Reattach the thermostat and other wires to the new heating element, reattach the back of the dryer, and your dryer is blowing hot air again. Upon removing the old heating element is was clear it was damaged as the top three rows of heating coils were burnt. I'm on my fifth load of drying since yesterday's repair. Thanks.

very easy

Perfect!