7MMGDX655EW0 Whirlpool Dryer - Instructions

Removed the Lint filter, then lifted top panel and rested the panel against the wall.
Disconnected connector attached to the door panel.
removed screws, from both side of door panel and lifted door panel up and out.

Moved Idler pulley to the right taking tension off the drum belt, lift the drum out with the drum belt.
removed old drum felt seal and removed old residual glue, reglued and installed new Rear Drum Felt Seal.
Installed new Idler pulley Assembly and reassembled in reverse order.

Doing my home work, I was told if I was "handy with my hands" I could do the work. Start to finish required 3+ hours. The instructions were not specific to my unit therefore, I had to "guess". My first surprise was encountered on step 2 - removing the top. My top was attached to the "brains" of the drier and therefore could not be removed. I actually had to disconnect the brains to remove the top. My second surprise was that I had to remove just about everything before I could get to the vent, which by the way, was simple. I finally accomplished the task, but....

When the part arrived I opened it and just snapped it on.

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

Remove top then front panel kit goes on gas value 2 screws hold gas tube in place.

I followed the video. So easy..

Take the door off of the dryer. Lay it on a towel. Remove old gasket. Clean the channel the door gasket fits into with glue remover. Squeeze high temperature glue into the channel, let the glue set up. Put the new gasket into the channel, tape it down in a few places. Let it sit 24 hours for the glue to set up. Put the door back on. You can put the door on immediately as long as you don't use the dryer for 24 hours. Easy.

Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.

removed old gasket took door off 4 screws. cleaned seal area applied glue put on gasket easy

I easily popped the new handle on in 3 seconds

Replaced with new handle in 10 seconds

The original door catch had broken and would no longer stay shut. Ordered the part from this site with ease. Very easy to replace the broken door catch on my Amana dryer. Tool needed was a flat head screwdriver to loosen the cover, remove broken piece and easily replace with new part. Followed the video and it was back to normal operation within minutes.

Took apart front of cabinet, set aside. Undid the belt drive. Removed the drum. Noticed rear seal was with large gap where it wore away, causing the lint to leak onto the interior of cabinet. Ordered a new seal, removed old seal, prepped for new seal. Used spring clamp to hold new one on place. Applied the glue to hold seal in place waited 24 hrs to dry. Reinstalled drum, put cabinet back together. Plugged in ran whisper guiet.

Removed old seal and replaced with new one. Save yourself time and get some acetone to remove old glue works great!

Replacement handle snapped right back in place. Took about 2 seconds.