DDG5180RAL Whirlpool Dryer - Instructions

I removed the right side panel and top panel from the dryer. I removed the 2 wire and 3 wire connectors from the 2 coils. I removed the bracket holding the 2 coils, replaced the 2 coils, and replaced the bracket. I reconnected the wires to the appropriate coils and replaced the side and tops panels on the dryer. The dryer now lights every time the dryer calls for heat.

removed top cover 2 screws removed back removed 2 wires 1screw on timer easy

Unplugged the machine.
Removed four screws from the top of the machine to uncover the top of the machine.
Pulled the leads off the broken switch.
In the future I will make a note of which lead goes where. There are only two ways.
Went to PartSelect.com and found the part in less than a minute by using their part finder.
Placed the switch through the original opening in the machine and reattached the leads.
Reattached the cover. Plugged the machine back in. Turned the switch and it started right up.

As many of the other posts here on this website mentioned, I had the same problem of the dryer not heating up. I removed the front panel (4 screws on each side inside of door - easy - followed instructions) and once off I was able to view the igniter glowing properly so I knew the starter/igniter was not the issue. Everything I read then suggested that it must be the two terminal gas valve coil, and sure enough it was. Ordered part -- got it in literally a couple days -- removed bracket (two screws) put in new coil -- turned it on -- works great. Could not have been easier. This is a great website and would recommend it to everyone who is a Do It Yourselfer.

i read some of previous customer problems and fixes pulled the front cover off found coil's location when i turned on drier you could see the ignitor getv hot but burner would not ignite unless i put a little pressure on secondary coil when i let go of coil flame would go out. ordered 'M' series new style coil kit came in in about three days installed parts drier workng good i would reuse parts select agian thanks

Really an easy fix. 2 5/16" screws hold the cover on below the dryer door. From here it's easy access to the gas element. 2 more screws for the valve cover and disconnected the attached wires to the gas coil valves. slip the news ones in place, re-attach the wires and install the holder.Tested the dryer and it fired right up. Put panel back in place and the wife is happy it didn't cost us more than just the parts. Yep, she's a lucky girl. ;0)

I removed the front panel and the top of the dryer, pulled the drum forward and removed the old rear drum bearing then inserted the new rear drum bearing. I didn't replace the washers or the retaining ring in the back. Put the drum shaft into the new rear drum bearing. Put the front panel and the top in place and started using the dryer again.

took old socket out, ordered replacement part, dual socket no longer available. Turn off power to appliance, attach new single light socket, screw light socket and light socket holder back into place. Turned on power and it worked. No instructions included in packet, attached wrong first time, blew fuse, attached socket a different way, and it worked.

After ensuring all 5 temp sensors were not open, replaced the timer assy by removing the back of the control section. ( 5 screws ) . removed both wire connectors and 1 screw. removed the old timer assy and knob. put old knob on new timer, installed into slots, installed screw and replaced wire connectors. replaced back panel and vent hose, applied power. Works like new

Removed filter as for cleaning. Replaced with new filter. NO TOOLS REQUIRED!

Opened up dryer for access to all components and tested. All checked good. Put back together and tested and igniter came on but no flame. Purchased two new coils and tested again. No flame. Purchased complete valve assembly and replaced old one. Tested again and viola, success! TY PartSelect for exact replacement part.

Checked out the coil seemed ok. So I replaced the radiant flame sensor. No change. Then I replaced the High limit sensor still the heat was not staying on. I read some were in the troubleshooting guide that the coil can test good, but can still malfunction. So that was it new coil fix it, works like a new Dryer again.

Thanks to reports from others, I concluded that most likely the gas ignition coils (one or both) were no longer functioning properly. I replaced both with the 'M' Series New Style Coil Kit which is about 1/2 the price of either coil individually -- yes,true,go figure! The actual replacement took only about 10 minutes. What was most difficult and took the most time was the removal of the front panel of the cabinet -- this was difficult only because there were no instructions in my owner's manual (or any other source I could find) and it took me awhile to figure it out. Now I could do the whole job in about 20 minutes! The detailed instructions from others as to the process of replacing the coils was invaluable -- I don't know if I would have been able to figure that out on my own. But most important was the information that enabled me to diagnose the problem in the first place. Thank you, all you previous comment contributors.

pulled out old socket and replaced supposed to be a duel socket but no longer exists

The repair in retrospect was very easy. Not knowing alot about the dryer I made one mistake. I put the bearing in backwards and broke the rubber gasket. After ordering a new gasket and paying close attention to what I was doing it worked out fine. Saved me about $200 for a repairman.