NG2119 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Newt from Daphne, AL
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Dryer would not come on
When the dryer stopped working, I checked the two switches to see if they were good. The start button checked out OK but the switch on the door read bad. Ordered the part with the part number and put on when it arrived. Just a matter of disconnecting and reconnecting three wires. Very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garold from Bothell, WA
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broken belt
I don't have the model number right now, but you video was fantastic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from minooka, IL
- Parts Used:
- WPY54414
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
dryer was making a real loud grinding noise, like nails on a chalk board.
Really easy popped the lid with a flat head screwdriver, then marked wires for door light and switch, took 2 5/16 bolts to remove front door, then 4 bolts also 5/16 to remove front panel but be care ful and remove drum belt then take panel and drum out. Then took a set of ring pliers to remove wheel slapped new one on.then reverse sreps to assemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Arlington, TX
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door Latch broken
Ordered part ( door latch ) flowed instructions easily fixed same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Hamden, CT
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Male end of door catch broke
First, I replaced the male end which was just two screws and simple replacement of pushing the fastener into the door frame. When finished I noticed the female end was damaged as well. Glad the female part came as well. This required taken off the front trim around the door (four screws - 2 each side) and then the door. The installing of the female end was easy with a little push. The damaged female end was already hanging out so easy to grab and remove. Otherwise I would have had to remove the front panel. Note You need to put the door trim back on before reattaching the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lakewood Village, TX
- Parts Used:
- WPY54414
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broken Idler pulley
removed front, top cabinet, drum, belt and motor. replaced idler pulley on motor. replaced motor, belt, drum and cabinet parts. test ran fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Uncasville, CT
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer not turning on.
Researched the common problem with "dryer not turning on", and tested the top three problems. Removed the dryer front casing and door, unbolted front dryer plate. Used a volt meter on two of the temp gauges, which were fine. Removed the upper back plate of the dryer to the wiring for the knobs and buttons. Used the volt meter on the dryer start button, which was also fine. Went back around to the front and removed the door switch. Tested it with the volt meter and bingo. Replaced that part, dryer works like normal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from phoenix, AZ
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the plastic latch broke
im a car mecanic it was easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from st. louis, MO
- Parts Used:
- WPY54414, WPW10121334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
excessive squeeling noise
replaced idler puller and washers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerry from New Braunfels, TX
- Parts Used:
- 56000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Wife let ink pin fall through lint trap and started dryer it broke fan.
Pulled off front of dryer because it made loud noise, lifted clothing drum removed cover for fan and order from model number on fan and replaced. 30 min with help from my son.
Was this instruction helpful to you?
Thank you for voting!
Blower wheel broken and rubbing on housing.
Removed front of dryer, first the lower then the upper front covers. Removed front drum support, front blower housing cover. Removed belt, and then motor with housing and blower wheel attached. Broke wheel and cover off motor, placed motor in vise to remove threaded nut from motor drive shaft (nut was seized). Reinstalled motor and belt. Installed new housing and blower wheel. Reassembled dryer. Note if old blower wheel had come off repair would have taken half the time and been significantly easier to perform.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Middletown, NY
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Dryer did not tumble.....Loose ....worn Belt
Fast delivery,,,, Easy installation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Shelbyville, KY
- Parts Used:
- WP40111201, W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Slipping drum, and broken door switch
Just like in the video. A very simple repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from Walters, OK
- Parts Used:
- WP40111201
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Dryer wouldn't tumble
I consulted the instructional video before starting to take the dryer apart. My model is older than the one used in the video but it was still very helpful. Putting the belt on was fairly easy; however, I didn't know I also needed a rear drum wheel as well so while the belt is installed, the dryer still doesn't tumble when anything is in it. Off balance without 2nd rear drum wheel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from Somersworth, NH
- Parts Used:
- WPY54414, WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Idler pulley was sticking on shaft, causing a squeaking sound
removed front panels, open the top of dryer. Removed the three screws holding blower panels and removed them. Then removed belt, drum and replaced the pulley. In reverse order reinstalled the parts. Done all is quit and no more squeak.
Was this instruction helpful to you?
Thank you for voting!