NG2119 Whirlpool Dryer - Instructions

Just snapped the new plastic latch into the hole (the hole was there because in trying to extract the old latch, it fell into the inside of the door). Took two seconds. Order to arrival of the part took only 22 hours!

First - I did some research on line as to the possible problem with this dryer.
I had already taken the front apart before, so I knew what was needed to remove the door and front.
Remove the 2 screws that hold the dryer door in place with a Phillips screwdriver. Remove the two screws on the opposite side of the door also. Place the door out of the way. The front panel of the dryer now tilts forward. The front panel sits on two clips, tilt forward and lift out of place. The door switch has two prongs that hold it in place, pinch the prongs and the switch slides out. Disconnect the two wires on the switch and connect the wires to the new switch. The new switch slides into place. I tested the new switch before I put it all back together. Took me no longer than 15 minutes.

When I first heard it sqweeling I tokk off bottom cover and peeked around the turned it on and it seemed to be coming from a back roller,I sprayed a little wd-40 and it went away,for a day ! Then I found parts select on line and found the problem. The belt had worn into the roller almost to the shaft. I ordered the roller and belt and watched the very helpful video and it took about 15 minutes!parts $29. 00 Piece and quiet without calling service guy priceless !! Thanks steven l. I. Ny

This was real easy just slid the latch in front panel and attached to latch assembly to the door. The repair was about 45 seconds.

Pushed in the Door Catch, and it was fixed.

Installing the new switch was a snap. With the dryer unplugged, open the top using a putty knife to release the 2 clips - one on each side. Lift the top and support it to stay open. Next, note the wire color and location for each of the 3 wires. Remove each wire from its prong on the bad switch by gripping the connector with pliers and pulling off. Next remove the bad switch by squeezing the tabs on the sides of the switch to release it. The switch removes to the front of the dryer. Install the new switch in the same method and reconnect the wires as before making sure the colors go back on the same prongs. I had to replace one of the connectors with a larger one (that came with the switch) since one of the prongs on the new switch was larger than the orginal (bad) switch. To do this, I cut the old connector off, stripped the end of the wire, and crimpted on the new connector. I had to be careful not to waste too much wire since there was very little slack to work with.

After ordering the part, I read the information left by other users. I used a screw driver to pop out the piece, and then put the new latch in the opening. A gentle pop with the side of my hand, and the door latch went right into place. Who knew there was a second door latch on the other side that could've been used?

Too simple to describe.

I did a quick research online and found PartSelect to have the best price. I ordered my part on Monday 8/6 and to my tremendous surprise FedEx delivered it Tuesday 8/7!! I did not pay for overnight delivery. My son happened to come by that day and he took a small flathead screwdriver, pried the old one out and inserted the new part. Done in 5 minutes! PartSelect will be my supplier from now on.

noticed that male half was in good working order, so I just snapped in the new female half; without any tools. easy repair!

Replace with new latch.

I consulted the instructional video before starting to take the dryer apart. My model is older than the one used in the video but it was still very helpful. Putting the belt on was fairly easy; however, I didn't know I also needed a rear drum wheel as well so while the belt is installed, the dryer still doesn't tumble when anything is in it. Off balance without 2nd rear drum wheel.

removed front panels, open the top of dryer. Removed the three screws holding blower panels and removed them. Then removed belt, drum and replaced the pulley. In reverse order reinstalled the parts. Done all is quit and no more squeak.

Well I first attemptede the repair wthout following the online instuction's, I dont recomend it.After some 30 minutes wasted trying to fit my hands in and droping the screw a couple of times, I decided it was time to remove the duct that supplies the air thru the lint trap, after that the repair was a breeze

I ordered the belt, which arrived really fast! Took dryer apart, removed old belt, replaced with new belt. The hardest part was remembering how to put the dryer back together! I think next time I will video the taking apart process so I can see how it goes back! This was the 2nd belt in about 18 years, the dryer works fine, and it sure is cheaper than a whole new dryer! Thanks for saving me money again! Really helps in these hard economic times!