HE4330 Whirlpool Dryer - Instructions

i took the front off the dryer took belt loose took the tub out the plastic nut on the blower wheel striped out so i took the blower housing apart along with the motor got vise grips on blower wheel replaced motor blower wheel belt and belt tenchinor and spring cleaned all the lint put it back together works fine

The repair went better than expected. I watched the video of how to replace the dryer belt and although it wasn't exactly the same, just by watching the video I was able to find my way through the process. Thank you very much for taking the time to create the video, it was very helpful and saved me a bundle of money by being able to do the repair myself.Thanks again!!! Dano, Melbourne Fl.

Watched the video from part select and it was easy. I will always order from part select, I loved the delivery time!! I ordered two belts, one for my dryer and one for my sons. . . My belt arrived the next day and my sons only took two days. . . Now that is service. . Thank you part select

Once I realized the drum was to be removed, the actual repair was not difficult. Because of the location of the pulley, it's best to tilt the dryer. Snap ring pliers are required to remove the retaining ring on pulley. I pulled the damaged pulley from the bearing. A small gear puller was needed to removed the frozen bearing. Lightly oil the new bearing. Installing the drum is a challenge because of the loose belt. I used paint tape to hold the belt on the drum. Download the service manual for good exploded parts views.

I took the dryer apart and used the video on the website that helped a lot on how to install the belt and then we put it back together and dryer works great.

I noticed my dryer wasnt turning so I decided to take it apart to see if I could fix it, I noticed my belt was almost to the breaking point and there was black dust everywhere. I looked at the idler pulley wheel and it didnt look right so i decided to replace that, the belt and noticed the felt pads were gone also and that can also effect the dryer turning so I replaced them also and put it all back together and it was working like it was brand new!

I openned the dryer and look for the problems. I found out the idle pulley was severly damaged. the driving belt was still ok however a piced of the belt backing was erroded. i found Part Select website and contact. The website is owsome! realy easy to follow and get youn to your needed parts. Customer service and the sales people are great. Also the video on the website is great and very easy to follow, they teach you how to install the parts. I had a very good experience with Part Select company. Thanks!

I was amazed just how easy it was. It would have been much quicker if I had a nut driver instead of a wrench. The video was great. Thank you!

for a while the dryer was really loud when on. i took the front cover, and could pin point it to the idler pulley wheel. i would squirt some wd 40 on the wheel just to get by. one day the dryer stopped turning so i thought the belt broke. after following the instructions on this site on now to take off the front panel, and tub holder (the panel that has the lint trap in it, i was able to take out the tub and find that the pulley wheel had broke apart. i ordered the new part and got a new belt at the same time. why not replace while i had it apart. i didnt have snap ring pliers to remove the snap ring so i got 2 small finishing nails that would fit in the holes and was able to pull apart the ring and get it off. i slid on the new wheel, and put the snap ring back on. ii watch the video on how to replace the belt and it was a sinch. the dryer was already apart and to fix it, took about 15 min. for $18 in parts, the dryer has never sounded better.parts select saves me money everytime.

I just followed the intructions from the video on the website. That made the replacement easy.

I did it just like the man in the video that was sent via e-mail by ParSelect,.

Removed the front of the dryer. Took out the drum. Now everything inside is easy to get to. You do not need to remove the top. Upon inspection we found that we also needed to replace both felts, teflon guides, drive belt, and both support rollers ans shafts. Basically we rebuilt the dryer. It's quiet now and working like new.