HE4330 Whirlpool Dryer - Instructions

removed the lower cover, tipped the dryer on its back for easier access, unscrewed the 2 mounting screws removed the heating element, installed the thermostat and and high tempt relay on new one replaced the wires reinstalled the new element, very simple

as described in video. Very well done. Thank you

Loosened the screws, took out the old one. It shorted out to back. Inserted the new one attached wires, Installed screws and it worked

removed the front of dryer panel below the door. Cleaned out all the lint. Pulled two screws with an extended nut driver. slid out the old element. I dentified the part . ordered, when the part came in I put a few simple componets on the new, slid it back in. Turned on the power to make sure it was working then reinstalled the front cover. works fine

Lifted the top of the dryer removed two screws and pulled the front of the Dryer forward. Slipped the new belt over the drum and over the motor pulley.
Pushed the front back in place and snapped the top of the dryer down and the job was complete.
I thought the part would take three days to get here.
It was delivered the day after I ordered it.

once I found where the heat element was, it took me a few mintues to remove the bad one and replace it with the new one that came before the due date. very good instruction in kit. Be sure and leave the old one hooked up until the new unit comes in so you can do a easy exchange of the wiring.

removed old element, relaced with new element , thermostat dryer works better than it has in along time

removed front of dryer, replaced old pully and put on new belt.

Leaned machine back and put blocking under machine to elevate. Removed two screws from front of bottom panel. Lift panel out and set aside. Next remove two bottom screws from door frame. Pull bottom of frame out and up to release. Remove wire clips from door light and switch. Set door frame aside. Inside drum, take three phillips head screws out, that hold filter frame in, remove filter frame. Next remove four front screws on drum alignment face plate. Set aside. Grasp drum and pull forward, off back guide rollers. Drum will drop down a little, reach in around drum and slide belt off. Remember to look in under drum to see proper placement of belt aroun motor shaft and idler pulley. Replace new belt around drum with ribs against drum. Route belt around motor shaft pulley, pull idler pulley toward motor and place belt around pulley smooth top runs against pulley. Reinstall everything you removed. Connect wires to door.

Fairly easy to repair once I figured out how to get it apart. The amazing part of this was searching the web for the part. I found PartSelect, ordered it at about 2pm Eastern time and the part arrived the next day! I will definitely use this service again.

Took apart front of dryer, took out tub, replaced pully wheel, put tub back in with new belt, and put front back on. I would recomend replacing wear pads when doing this type of job.

First - I did some research on line as to the possible problem with this dryer.
I had already taken the front apart before, so I knew what was needed to remove the door and front.
Remove the 2 screws that hold the dryer door in place with a Phillips screwdriver. Remove the two screws on the opposite side of the door also. Place the door out of the way. The front panel of the dryer now tilts forward. The front panel sits on two clips, tilt forward and lift out of place. The door switch has two prongs that hold it in place, pinch the prongs and the switch slides out. Disconnect the two wires on the switch and connect the wires to the new switch. The new switch slides into place. I tested the new switch before I put it all back together. Took me no longer than 15 minutes.

When I first heard it sqweeling I tokk off bottom cover and peeked around the turned it on and it seemed to be coming from a back roller,I sprayed a little wd-40 and it went away,for a day ! Then I found parts select on line and found the problem. The belt had worn into the roller almost to the shaft. I ordered the roller and belt and watched the very helpful video and it took about 15 minutes!parts $29. 00 Piece and quiet without calling service guy priceless !! Thanks steven l. I. Ny

Installing the new switch was a snap. With the dryer unplugged, open the top using a putty knife to release the 2 clips - one on each side. Lift the top and support it to stay open. Next, note the wire color and location for each of the 3 wires. Remove each wire from its prong on the bad switch by gripping the connector with pliers and pulling off. Next remove the bad switch by squeezing the tabs on the sides of the switch to release it. The switch removes to the front of the dryer. Install the new switch in the same method and reconnect the wires as before making sure the colors go back on the same prongs. I had to replace one of the connectors with a larger one (that came with the switch) since one of the prongs on the new switch was larger than the orginal (bad) switch. To do this, I cut the old connector off, stripped the end of the wire, and crimpted on the new connector. I had to be careful not to waste too much wire since there was very little slack to work with.

Too simple to describe.